Sponsored Content
Full Discussion: setup network interface
Operating Systems Solaris setup network interface Post 302281653 by lamoul on Thursday 29th of January 2009 08:41:18 AM
Old 01-29-2009
you know how to set to 100mb or 1000mb full duplex?

thanks again
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt (4 Replies)
Discussion started by: witt
4 Replies

2. IP Networking

Network Setup

I am moving a SUN 250 server from one location to another. The IP address has to change in order to make the server visible in the new building. The system administrator has given me the new IP address for the server, the DNS server IP and the default gateway IP. First question, is this all the... (2 Replies)
Discussion started by: pkappaz
2 Replies

3. IP Networking

network setup???

Hello everybody, I am a new unix user (Solaris 10). I was wondering if anybody can help me figure out how to connect to the network in my work place. I know my IP address, subnet mask, gateway, primary and secondary DNS addresses but I don't know how to enter these settings into my Solaris. ... (3 Replies)
Discussion started by: arash05
3 Replies

4. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies

5. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies

6. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies

7. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies

8. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies

9. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies

10. IP Networking

Can't setup new interface.

Hi all, Currently I am running Solaris 10 update 10 machine. My current ifconfig -a output is: ifconfig -a lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet 127.0.0.1 netmask ff000000 bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu... (1 Reply)
Discussion started by: Junaid Subhani
1 Replies
TXP(4)							   BSD Kernel Interfaces Manual 						    TXP(4)

NAME
txp -- 3Com 3XP Typhoon/Sidewinder (3CR990) Ethernet interface SYNOPSIS
txp* at pci? dev ? function ? DESCRIPTION
The txp interface provides access to the 10Mb/s and 100Mb/s Ethernet networks via the 3Com Typhoon/Sidewinder chipset. This driver supports the following cards: o 3Com 3CR990-TX-95 o 3Com 3CR990-TX-97 o 3Com 3CR990SVR95 o 3Com 3CR990SVR97 Basic Ethernet functions are provided as well as support for vlan(4) tag removal and insertion assistance, receive ip(4), tcp(4), and udp(4) checksum offloading, and transmit ip(4) checksum offloading. There is currently no support for transmit tcp(4) or udp(4) checksum offload- ing, tcp(4) segmentation, nor ipsec(4) acceleration. Note that hardware checksumming is only used when the interface is not in bridge(4) mode. Each of the host's network addresses is specified at boot time with an SIOCSIFADDR ioctl(2). The txp interface employs the address resolu- tion protocol described in arp(4) to dynamically map between Internet and Ethernet addresses on the local network. When a txp interface is brought up, by default, it will attempt to auto-negotiate the link speed and duplex mode. The speeds, in order of attempt, are: 100Mb/s Full Duplex, 100Mb/s Half Duplex, 10 Mb/s Full Duplex, and 10 Mb/s Half Duplex. The txp supports several media types, which are selected via the ifconfig(8) command. The supported media types are: media autoselect Attempt to autoselect the media type (default) media 100baseTX mediaopt full-duplex Use 100baseTX, full duplex media 100baseTX [mediaopt half-duplex] Use 100baseTX, half duplex media 10baseT mediaopt full-duplex Use 10baseT, full duplex media 10baseT [mediaopt half-duplex] Use 10baseT, half duplex SEE ALSO
arp(4), ifmedia(4), inet(4), intro(4), ip(4), netintro(4), pci(4), tcp(4), udp(4), vlan(4), ifconfig(8) HISTORY
The txp driver first appeared in NetBSD 2.0. BSD
August 21, 2003 BSD
All times are GMT -4. The time now is 10:34 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy