07-17-2008
@funibone
this thread is over 3 years old... and without the driver for the network cards your solution won't work either!
10 More Discussions You Might Find Interesting
1. IP Networking
dear sir
how many name server can be configured in single machine?
thank you very much.
sandeep goel (3 Replies)
Discussion started by: ask_goel
3 Replies
2. IP Networking
HI guys/gals
basic question
lets say i am running a network. lets say i am using Win Me.
how would i network Win Me to a computer that has linux and another that has 98 well the 98 is no problem but the linux well i have an idea but i am rusty with linux. No i have rusted out. Would you make... (1 Reply)
Discussion started by: pydyer
1 Replies
3. IP Networking
I am trying to network two solaris workstations(ultra sparc 5) at home. what shoud I use to build the one of workstations as a http and ftp server and to network with the other workstation?
(please explain to me in detail.. what kind of software or equipment do I need..)
Thanks
John (1 Reply)
Discussion started by: jung1975
1 Replies
4. UNIX for Dummies Questions & Answers
Hi,
I am trying to configure an ip address, netmask, and default gateway on my solaris machine. For example, in Linux I would do the following command:
#ifconfig eth0 xx.xx.xx.xx netmask 255.0.0.0
#add route or route add default xxx.xxx.xxx.xxx
In Solaris 10, I believe the commands are... (7 Replies)
Discussion started by: annointed3
7 Replies
5. Solaris
may i know what is the command for configure
new ip, subnet mask and gateway ??
thanks .. (3 Replies)
Discussion started by: Farbegas
3 Replies
6. IP Networking
hi all,
how do i make sure that the new routing should take effect on the os memory right away? what should i run after i add all the new "route add ....".
I have an example below:
bash-2.03# netstat -rn
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface... (1 Reply)
Discussion started by: itik
1 Replies
7. IP Networking
Hi all
Right, i need to admit Im c4p on networking. I hate it, always have, always will. Here's my problem
Ive got 3 hosts. A B and C. I need to directly contact host C from host A, but at the moment I have to ssh on to B, to then ssh on to C.
so, I need to set up host b, to forward... (3 Replies)
Discussion started by: sbk1972
3 Replies
8. Solaris
e1000g0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet 10.13.157.127 netmask ffffffc0 broadcast 10.135.151.191
ether 0:14:4f:a0:e3:3a
e1000g1: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 8
inet 10.13.157.227 netmask ffffffc0... (3 Replies)
Discussion started by: sunnybee
3 Replies
9. Solaris
Hi,
I have installed two solaris boxes in an VM.
First box is 10-1
Has two interfaces and in connected briged to the lan an d connected internal to an virtual lan.
Second box is 10-2
Has one interface.
Now what I wanted to do is a setup so that 10-2 connects through 10-1 to the lan.... (3 Replies)
Discussion started by: jld
3 Replies
10. IP Networking
Hi All,
Actually a very basic question this one. I've got a Solaris 10 x86 server box on a network. There are a group of other servers I need to connect to from it, but via a VPN connection. If I install a vpn client on my solaris box, can I configure the VPN connection so it only routes certain... (1 Reply)
Discussion started by: mikecouk
1 Replies
AN(4) BSD Kernel Interfaces Manual AN(4)
NAME
an -- Aironet 4500/4800 and Cisco 340/350 series wireless network driver
SYNOPSIS
an* at pcmcia? function ?
an* at pci? dev ? function ?
an* at isapnp?
DESCRIPTION
The an driver provides support for Aironet Communications 4500/4800 and Cisco Aironet 340/350 series wireless network adapters. This
includes the ISA, PCI and PCMCIA varieties. The 4500 series adapters operate at 1 and 2Mbps while the 4800 series and 340/350 series can
operate at 1, 2, 5.5 and 11Mbps. The ISA, PCI and PCMCIA devices are all based on the same core PCMCIA modules and all have the same pro-
gramming interface, however unlike the Lucent WaveLAN/IEEE cards, the ISA and PCI cards appear to the host as normal ISA and PCI devices and
do not require any PCMCIA support.
The PCMCIA Aironet cards require PCMCIA support. ISA cards can either be configured to use ISA Plug and Play or to use a particular I/O
address and IRQ by properly setting the DIP switches on the board. (The default switch setting is for plug and play.) The an driver has
Plug and Play support and will work in either configuration, however when using a hard-wired I/O address and IRQ, the driver configuration
and the NIC's switch settings must agree. PCI cards require no switch settings of any kind and will be automatically probed and attached.
All host/device interaction with the Aironet cards is via programmed I/O. The Aironet devices support 802.11 and 802.3 frames, power manage-
ment, BSS (infrastructure) and IBSS (ad-hoc) operation modes. The an driver encapsulates all IP and ARP traffic as 802.11 frames, however it
can receive either 802.11 or 802.3 frames. Transmit speed is selectable between 1Mbps, 2Mbps, 5.5Mbps, 11Mbps, or ``auto'' (the NIC automat-
ically chooses the best speed).
By default, the an driver configures the Aironet card to join an access point with an SSID of null string. For ad-hoc mode, in which sta-
tions can communicate among each other without the aid of an access point, the driver must be set using ifconfig(8).
For more information on configuring this device, see ifconfig(8) and ifmedia(4).
HARDWARE
Cards supported by the an driver include:
Aironet 4500 Series
Aironet 4800 Series
Cisco Aironet 340 Series
Cisco Aironet 350 Series
DIAGNOSTICS
an%d: init failed The Aironet card failed to come ready after an initialization command was issued.
an%d: failed to allocate %d bytes on NIC The driver was unable to allocate memory for transmit frames in the NIC's on-board RAM.
an%d: device timeout The Aironet card failed to generate an interrupt to acknowledge a transmit command.
SEE ALSO
arp(4), ifmedia(4), netintro(4), ifconfig(8)
HISTORY
The an device driver first appeared in FreeBSD 4.0, and then in NetBSD 1.6.
AUTHORS
The an driver was written by Bill Paul <wpaul@ee.columbia.edu>.
BSD
December 13, 2000 BSD