10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
2. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
3. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
4. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
5. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
6. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
7. Solaris
Dears,
i follow this to configure Network interface for my PC
O/S : Unix Sun Solaris
vi /etc/hostname.bge0
and write my ip
vi /etc/netmasks
and write my subnetmask
vi /etc/defautrouter
and write my gatwey
vi /etc/resolv.conf
and write my DNS
after i reboot My Computer ... (3 Replies)
Discussion started by: jenovaux
3 Replies
8. IP Networking
What are the steps between "ifconfig eth0 UP" and "net_device->open"?
ifconfig eth0 UP =>
ioctl(skfd, SIOCSIFFLAGS, &ifr) (ifr.ifr_flags = IFF_UP | IFF_RUNNING) =>
????? => what are these steps?
net_device->open
Thanks! (1 Reply)
Discussion started by: samuncle
1 Replies
9. UNIX for Advanced & Expert Users
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Discussion started by: sc2005
6 Replies
10. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
TXP(4) BSD Kernel Interfaces Manual TXP(4)
NAME
txp -- 3Com 3XP Typhoon/Sidewinder (3CR990) Ethernet interface
SYNOPSIS
txp* at pci? dev ? function ?
DESCRIPTION
The txp interface provides access to the 10Mb/s and 100Mb/s Ethernet networks via the 3Com Typhoon/Sidewinder chipset. This driver supports
the following cards:
o 3Com 3CR990-TX-95
o 3Com 3CR990-TX-97
o 3Com 3CR990SVR95
o 3Com 3CR990SVR97
Basic Ethernet functions are provided as well as support for vlan(4) tag removal and insertion assistance, receive ip(4), tcp(4), and udp(4)
checksum offloading, and transmit ip(4) checksum offloading. There is currently no support for transmit tcp(4) or udp(4) checksum offload-
ing, tcp(4) segmentation, nor ipsec(4) acceleration. Note that hardware checksumming is only used when the interface is not in bridge(4)
mode.
Each of the host's network addresses is specified at boot time with an SIOCSIFADDR ioctl(2). The txp interface employs the address resolu-
tion protocol described in arp(4) to dynamically map between Internet and Ethernet addresses on the local network.
When a txp interface is brought up, by default, it will attempt to auto-negotiate the link speed and duplex mode. The speeds, in order of
attempt, are: 100Mb/s Full Duplex, 100Mb/s Half Duplex, 10 Mb/s Full Duplex, and 10 Mb/s Half Duplex.
The txp supports several media types, which are selected via the ifconfig(8) command. The supported media types are:
media autoselect
Attempt to autoselect the media type (default)
media 100baseTX mediaopt full-duplex
Use 100baseTX, full duplex
media 100baseTX [mediaopt half-duplex]
Use 100baseTX, half duplex
media 10baseT mediaopt full-duplex
Use 10baseT, full duplex
media 10baseT [mediaopt half-duplex]
Use 10baseT, half duplex
SEE ALSO
arp(4), ifmedia(4), inet(4), intro(4), ip(4), netintro(4), pci(4), tcp(4), udp(4), vlan(4), ifconfig(8)
HISTORY
The txp driver first appeared in NetBSD 2.0.
BSD
August 21, 2003 BSD