Sponsored Content
Full Discussion: RedHat 9 Force full duplex
Operating Systems Linux Red Hat RedHat 9 Force full duplex Post 302090364 by zazzybob on Monday 25th of September 2006 09:00:51 AM
Old 09-25-2006
Can you execute

ethtool -s eth0 speed 100 duplex full autoneg off

then post the output of

ethtool eth0

Cheers
ZB
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

How to configure Full Duplex and TCP/IP

We are using ZIX 4.3.3 and we need to configure the NIC for ful duplexing and we also need to configure it for a TCP/IP default gateway and DNS server to acccess the Interent. Can you please tell me the commands and procedures for configuring this? Thanks Marc (2 Replies)
Discussion started by: marc3483
2 Replies

2. UNIX for Dummies Questions & Answers

Full duplex at HUB?

Ok at the moment I have a hub whit 5 computers connected to it. It's a 10/100 NetGear hub. Ok I heard that there is some command I can run or a file I edit or something like that. But what the command/file/script/whatever does is tells you what connect speed it's connecting to the hub to. ... (4 Replies)
Discussion started by: merlin
4 Replies

3. UNIX for Dummies Questions & Answers

Full Duplex Howto

Dear Members, I was reading a few posts and saw something about installing two Nics so one could use Full Duplex. I remember back in the day of dial up, you could have two modems and use one for upstream and one for downstream. This was called shotgunning. It seems that you can now do the same... (4 Replies)
Discussion started by: Phobos
4 Replies

4. Programming

full -duplex ?

what is meant by full duplex and half duplex? b'coz in differences b\w hub and switch ,i heard lot this duplex word so please help me (1 Reply)
Discussion started by: parvathy
1 Replies

5. Solaris

100 gigabit full duplex

How can I tell on Solaris 9 sparc if my nics are running 100 gigabit full duplex... (4 Replies)
Discussion started by: csaunders
4 Replies

6. Solaris

How to force a full duplex

I need to change some Ip addresses for my servers to reflect in the NIS map. I also need to force full duplex on the 10/100 cards & 1/2 duplex in the 10 cards. I can change the IP by doing ifconfig <NIC card > plumb up <newip>. Not quite sure on how to force the full / half duplex & how to... (2 Replies)
Discussion started by: Remi
2 Replies

7. SuSE

configure full duplex

How do I configure full duplex on suse 8.2 I tried ethtool -s eth0 speed 100 duplex full autoneg off the above works but when I reboot the machine the configure was lost. How do I configure full duplex so that when the machine get rebooted the configuration will stay. My interface... (4 Replies)
Discussion started by: hassan2
4 Replies

8. UNIX for Advanced & Expert Users

How to set full duplex for solaris 5.5

I would like to change half duplex to full duplex on solaris 5.5. I tried with below commands but they didnt work on solaris 5.5. #ndd -set /dev/le adv_100fdx_cap 1 (6 Replies)
Discussion started by: csreenivas
6 Replies

9. Solaris

How to find half duplex or full duplex

Hi, How to find whether the server is running with half duplex or full duplex. I tried with the following command ndd -get /dev/ but am not getting any output,. Is the command correct? Also let me know how to change from half to full duplex. (1 Reply)
Discussion started by: rogerben
1 Replies

10. UNIX for Advanced & Expert Users

100Mb/s full duplex link

Hi, I have been trying to connect two computers directly through their LAN cards. One is a 3com 3c905c 10/100 Mbit/s card and the other is an Intel i217-lm 10/100/1000Mbit/s card. I have connected them through a CAT 6 cable. Whenever autoneg is turned on, the PCs connect in the 10Mb/s mode, and... (7 Replies)
Discussion started by: jamie_123
7 Replies
TXP(4)							   BSD Kernel Interfaces Manual 						    TXP(4)

NAME
txp -- 3Com 3XP Typhoon/Sidewinder (3CR990) Ethernet interface SYNOPSIS
txp* at pci? dev ? function ? DESCRIPTION
The txp interface provides access to the 10Mb/s and 100Mb/s Ethernet networks via the 3Com Typhoon/Sidewinder chipset. This driver supports the following cards: o 3Com 3CR990-TX-95 o 3Com 3CR990-TX-97 o 3Com 3CR990SVR95 o 3Com 3CR990SVR97 Basic Ethernet functions are provided as well as support for vlan(4) tag removal and insertion assistance, receive ip(4), tcp(4), and udp(4) checksum offloading, and transmit ip(4) checksum offloading. There is currently no support for transmit tcp(4) or udp(4) checksum offload- ing, tcp(4) segmentation, nor ipsec(4) acceleration. Note that hardware checksumming is only used when the interface is not in bridge(4) mode. Each of the host's network addresses is specified at boot time with an SIOCSIFADDR ioctl(2). The txp interface employs the address resolu- tion protocol described in arp(4) to dynamically map between Internet and Ethernet addresses on the local network. When a txp interface is brought up, by default, it will attempt to auto-negotiate the link speed and duplex mode. The speeds, in order of attempt, are: 100Mb/s Full Duplex, 100Mb/s Half Duplex, 10 Mb/s Full Duplex, and 10 Mb/s Half Duplex. The txp supports several media types, which are selected via the ifconfig(8) command. The supported media types are: media autoselect Attempt to autoselect the media type (default) media 100baseTX mediaopt full-duplex Use 100baseTX, full duplex media 100baseTX [mediaopt half-duplex] Use 100baseTX, half duplex media 10baseT mediaopt full-duplex Use 10baseT, full duplex media 10baseT [mediaopt half-duplex] Use 10baseT, half duplex SEE ALSO
arp(4), ifmedia(4), inet(4), intro(4), ip(4), netintro(4), pci(4), tcp(4), udp(4), vlan(4), ifconfig(8) HISTORY
The txp driver first appeared in NetBSD 2.0. BSD
August 21, 2003 BSD
All times are GMT -4. The time now is 06:24 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy