10 More Discussions You Might Find Interesting
1. SCO
hi
How can I use my USB Flash memory in Sco 5.0.6
tanks (1 Reply)
Discussion started by: moein.mojtaba
1 Replies
2. SCO
Years ago I set up USB printing for SCO UNIX OpenServer 5.0.7 for a client--but I've misplaced my notes on how to do this! Maintenance Pack 5 is installed. I need step-by-step instructions to proceed. I've searched the SCO Knowledge Base site and found nothing there or elsewhere on the Web. (3 Replies)
Discussion started by: Transpower
3 Replies
3. SCO
Hi
I am trying to install NIC FastNic 10/100 PCI Ethernet driver into PCI# 3 of the GA-SIML Rev 1.0 Motherboard on 1GB Hard-disk driveI have following the instruction on the CD-Disk and when I added NIC by netconfig and I do not know what is the following question:
PCI BUS#
DEVICE#... (3 Replies)
Discussion started by: TinhNhi
3 Replies
4. SCO
Has anyone installed SCO 6 in Virtualbox? I was quite successful with 5.0.6 but then when I tried SCO 6, it will not report any nic (I am using resmgr to see who is there). The available cards under virtualbox are pcnet-pci II and II, and a few intel/pro 1000s. I have installed the maintenance pack... (1 Reply)
Discussion started by: dalek
1 Replies
5. UNIX for Dummies Questions & Answers
Can someone help me with instructions on how to access a USB flash drive in SCO Unix 5.0.5? I need to copy ASCII text files that have been zipped onto the USB drive for transfer to a Windows computer. (0 Replies)
Discussion started by: jlodata
0 Replies
6. Programming
Hi
I am writing a piece of code using gcc-3.4.4 which uses usb library (-lusb) to interact with a small robot, getting inputs from sensors and sending commands back to motors.
Now my problem is that when I use ncurses library in my code to get use of keyboard functionalities, the usb inputs do... (1 Reply)
Discussion started by: omoallemi
1 Replies
7. SCO
is it possible to access an usb flash disk under sco unixware 7.11?
and how to do?
any help is apreciated (0 Replies)
Discussion started by: nabil_boussetta
0 Replies
8. SCO
I have a USB,can i use it in the sco unix 5.0.6? (1 Reply)
Discussion started by: fresh
1 Replies
9. UNIX for Dummies Questions & Answers
FreeBSD 4.5
i installed my sound drivers (which are onboard) with the following lines in my kernel
device pcm
options PNPBIOS
then cd /dev
sh MAKEDEV snd0
output from cat /dev/sndstat show the devicedriver (correct one)
ok this works nice
untill i enter my kde and want to play a... (1 Reply)
Discussion started by: termiEEE
1 Replies
10. UNIX for Dummies Questions & Answers
How do I install an intel nic on sco 5.0.5 it did not detect when i installed the program:confused: (2 Replies)
Discussion started by: recono1
2 Replies
EHCI(4) BSD Kernel Interfaces Manual EHCI(4)
NAME
ehci -- USB Enhanced Host Controller driver
SYNOPSIS
ehci* at cardbus? function ?
ehci* at pci? dev ? function ?
usb* at ehci?
DESCRIPTION
The ehci driver provides support for the USB Enhanced Host Controller Interface, which is used by USB 2.0 controllers.
EHCI controllers are peculiar in that they can only handle the USB 2.0 protocol. This means that they normally have one or more companion
controllers (i.e., ohci(4) or uhci(4)) handling USB 1.x devices. Consequently each USB connector is electrically connected to two USB con-
trollers. The handling of this is totally automatic, but can be noticed since USB 1.x and USB 2.0 devices plugged in to the same connector
appear to connect to different USB busses.
SEE ALSO
cardbus(4), ohci(4), pci(4), uhci(4), usb(4)
HISTORY
The ehci driver appeared in NetBSD 1.6.
BUGS
The support for hubs that are connected with high speed upstream and low or full speed downstream (i.e., for transaction translators) is lim-
ited.
BSD
Aug 10, 2008 BSD