Sponsored Content
Operating Systems Solaris No network interface detected Post 87345 by reborg on Saturday 22nd of October 2005 07:41:39 PM
Old 10-22-2005
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Network Interface

Hi ! Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !! Thx in adivance ! Witt (4 Replies)
Discussion started by: witt
4 Replies

2. UNIX for Advanced & Expert Users

Network interface goes down intermittently

Hi all, I'm using an HP Proliant server with double NIC and Debian 5 (Lenny) as its OS. I used link bonding on it for several years with no problem. Today, (now only one interface connected to switch) the interface went down. I restarted networking service (/etc/init.d/networking restart) and... (7 Replies)
Discussion started by: mjdousti
7 Replies

3. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ? Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies

4. UNIX for Advanced & Expert Users

Multiple interface same network

hi I have a question, eth0 : 192.168.2.10 eth1: 192.168. 2.11 subnet : 255.255.255.0 eth0 and eth1 plug same swich I want communication between the two interface one host examp : ping 192.168.2.10 -I eth1 ping 192.168.2.11 -I eth0 but not respons.. pls helme (3 Replies)
Discussion started by: sadosan83
3 Replies

5. UNIX and Linux Applications

Access to network interface (Mac-network)

Hi, I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan. For that I must access to network interface to develope my personal stack based on standard 802.15.4. Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies

6. IP Networking

Network interface-

Hello, Please what's the difference between: AND Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies

7. IP Networking

network interface -

Hello, Please, how can i create a network interface with a routable IP address on linux (ubuntu) ? AND How can i desactivate an interface? Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies

8. Solaris

No network cable But Network interface is UP and Running

I've one Netra 240 After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces. I tried to restart and plumb/unplumb with no luck. ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies

9. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies

10. AIX

Misconfiguration detected Adapter interface name en 3 Adapter offset 0

Hi, We had a hardware problem with an IBM System p5 server, with AIX 5.2 We restore from a tape the last backup we had, but the server does not boot up as expected. The server try to mount some directories from a storage, but could not comunicate with them, we check the FC and everything is... (12 Replies)
Discussion started by: trevian3969
12 Replies
URL(4)							   BSD Kernel Interfaces Manual 						    URL(4)

NAME
url -- Realtek RTL8150L USB Ethernet driver SYNOPSIS
url* at uhub? urlphy* at mii? DESCRIPTION
The url driver provides support for USB Ethernet adapters based on the Realtek RTL8150L USB-ether bridge chip. The url driver supports the following adapters: CompUSA USBKR100 GreenHouse GH-USB100B Melco Inc. LUA-KTX Sitecom LN013 For more information on configuring this device, see ifconfig(8). DIAGNOSTICS
url%d: watchdog timeout A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the transmission before a timeout expired. url%d: no memory for rx list The driver failed to allocate an mbuf for the receiver ring. SEE ALSO
arp(4), mii(4), netintro(4), usb(4), ifconfig(8) HISTORY
The url device driver first appeared in NetBSD 1.6. AUTHORS
The url driver was written by Shingo WATANABE <nabe@nabechan.org>. BSD
September 18, 2006 BSD
All times are GMT -4. The time now is 09:07 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy