08-07-2014
Sounds like a problem with your router/modem dropping packets. DNS, which IIRC uses UDP, is going to be hurt hard by that.
When's the last time the router or the modem were rebooted?
10 More Discussions You Might Find Interesting
1. Cybersecurity
At the moment, I have three computers at home. I want to use boardband for my three computers. But I don't want to use network at home. I have been looking for a product which call OriNoCo USB Cilent. How do I connect to the internet with my computer??
If I post this in a wrong place, please... (0 Replies)
Discussion started by: him
0 Replies
2. IP Networking
Hi,
I have a laptop with a Linksys Wireless G PCMCIA card and a cable connection goin into a router and then a patch lead from the router going to a Linksys Wireless G access point IP 192.168.1.245 with DHCP disabled.
I can connect to the access point from the laptop, but how do I get the... (1 Reply)
Discussion started by: perleo
1 Replies
3. UNIX for Dummies Questions & Answers
I installed solaris 10 x86 on my dell laptop on a partition alongside windows xp. I am able to connect to the internet in xp with both my ethernet local area connection as well as through my wireless network card. But, however i do not have clue as to how to go about it in solaris.
i did not... (0 Replies)
Discussion started by: stakes20
0 Replies
4. Linux
I am running FC4:
Linux maincomp 2.6.13-1.1532_FC4smp
I recently changed the OS from windows XP, and have a feeling that for some reason my wireless network card is slower on Fedora Core 4. The Belkin PCI 802.11b card was automatically detected and configured by FC4 when I installed the OS,... (0 Replies)
Discussion started by: dangral
0 Replies
5. Cybersecurity
Hi all,
How can I monitor packet traffic on my wireless router?
Some info
- my wireless router is netgear wgr614
- everyone can connect it i.e. no password required
- I would like to see where they connect, how they are using the internet connection
I installed wireshark and captured... (3 Replies)
Discussion started by: SaTYR
3 Replies
6. Hardware
hi
Howto identify wireless network card using Live CD? (2 Replies)
Discussion started by: ccc
2 Replies
7. Ubuntu
Hi,
I am a new to Ubuntu linux and trying to learn it. I am using ubuntu 10.04. I am getting problem in setting my wireless network. I set it up properly and was working fine. But suddenly it stopped working, though the wireless icon saying that it is connected, but can't load any page. I... (2 Replies)
Discussion started by: linux_learner
2 Replies
8. Red Hat
Hi,
I am trying to set up a wireless internet connection on my centos OS (6). I can connect via the copper using the internal LAN but cannot get the wireless connection working.
The 2 files that I have configured are:
My wpa_supplicant.conf:
ctrl_interface=/var/run/wpa_supplicant... (1 Reply)
Discussion started by: Duffs22
1 Replies
9. Hardware
Good Day All,
There are numerous results when searching google on this issue, however, none seem to have a solution.
I have read until my eyes bleed and banged my head on the table more than once! :)
I am hoping to resolve this issue -- or at least have a decent workaround.
It is a real... (13 Replies)
Discussion started by: RogerBaran
13 Replies
10. Ubuntu
I run lubuntu from usb (try lubuntu, it's not install on my pc )
And i try to connect to network
I see the network name
And i put the pass
But it's not connect..
I tried to open hot spot on my phone and try to connect and it's not connect
I have edumax n150
Try to install new driver -... (0 Replies)
Discussion started by: popcoern
0 Replies
CNW(4) BSD Kernel Interfaces Manual CNW(4)
NAME
cnw -- Netwave AirSurfer wireless network driver
SYNOPSIS
cnw* at pcmcia? function ?
DESCRIPTION
The cnw interface provides access to a theoretical 1 Mb/s wireless Ethernet network based on the Netwave AirSurfer Wireless LAN (formerly
known as the Xircom Netwave Wireless LAN).
Note that the driver does not support newer devices such as the Netwave AirSurfer ``Plus'', or the BayStack 650/660. These devices are sup-
ported by the awi(4) driver.
Netwave devices are not compatible with IEEE 802.11 wireless networks. Also note that there are Netwave devices with different wireless fre-
quency, depending on the radio band plan in each country.
The card uses 36K of I/O memory mapped to the card. You may need to increase memory space available to the PCMCIA controller. See pcmcia(4)
for details.
In use, the cards appear to achieve up to a 420Kb/s transfer rate, though a transfer rate between 250Kb/s and 350Kb/s is typical.
The card operates in the 2.4GHz frequency range and is subject to interference from microwaves, IEEE 802.11 wireless network devices, as well
as earth. For example, it seems that IEEE 802.11 channel 14 conflicts with Netwave (US frequency). They interfere with each other if they
are both operated in the same geographic region, causing weird packet loss. You may be able to avoid the interference with IEEE 802.11
devices, by changing the IEEE 802.11 channel.
HARDWARE
Cards supported by the cnw driver include:
Xircom CreditCard Netwave
NetWave AirSurfer
DIAGNOSTICS
cnw0: can't map memory Indicates that the driver was not able to allocate enough PCMCIA bus address space into which to map the device. See
pcmcia(4) and increase memory available to the PCMCIA controller.
SEE ALSO
arp(4), awi(4), inet(4), intro(4), pcmcia(4), cnwctl(8)
BSD
January 5, 1997 BSD