03-09-2013
see the other interface o/p:
ossuser@PNR1RAD01 # ifconfig -a
lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
e1000g0: flags=1000803<UP,BROADCAST,MULTICAST,IPv4> mtu 1500 index 2
inet 10.200.2.73 netmask fffffff8 broadcast 10.200.2.79
e1000g1: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 3
inet 10.200.3.58 netmask ffffffc0 broadcast 10.200.3.63
And one more observation:
root@PNR1RAD01 # dladm show-dev
e1000g0 link: down speed: 0 Mbps duplex: half
e1000g1 link: up speed: 1000 Mbps duplex: full
e1000g2 link: unknown speed: 0 Mbps duplex: half
e1000g3 link: unknown speed: 0 Mbps duplex: half
This link shows down in this command o/p although in ifconfig o/p it shows up but noot the running state as e1000g1 interface.
10 More Discussions You Might Find Interesting
1. Solaris
Hi
I'm having a big trouble running a configuration tool (ftamtool) which uses xview on sunos 5.8, it refuses to start and says: XView error: could not load font 'FONT_FAMILY_SANS_SERIF...
How to force the program to use installed fonts and where are fonts installed available to use ?
... (0 Replies)
Discussion started by: andryk
0 Replies
2. IP Networking
I'm trying to plumb a new interface bge1 on my machine:
root@obms2-com-indianapolis-in:/root# ifconfig -a
lo0: flags=1000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4> mtu 8232 index 1
inet 127.0.0.1 netmask ff000000
bge0: flags=1000843<UP,BROADCAST,RUNNING,MULTICAST,IPv4> mtu 1500 index 2
inet... (3 Replies)
Discussion started by: R37ribution
3 Replies
3. Shell Programming and Scripting
I am looking to get a report on autosys jobs in RUNNING state b/w certain time frame (timeA and timeB).
What I am after is the list of all the jobs that ran between AND during timeA and timeB.
Jobs within the timeframe could either:
A: STARTING --> RUNNING --> SUCCESS/FAILURE etc..
B: ... (0 Replies)
Discussion started by: rgilan01
0 Replies
4. Programming
I am looking to get a report on autosys jobs in RUNNING state b/w certain time frame (timeA and timeB).
What I am after is the list of all the jobs that ran between AND during timeA and timeB.
Jobs within the timeframe could either:
A: STARTING --> RUNNING --> SUCCESS/FAILURE etc..
B: ... (0 Replies)
Discussion started by: rgilan01
0 Replies
5. Solaris
I am looking to get a report on autosys jobs in RUNNING state b/w certain time frame (timeA and timeB).
What I am after is the list of all the jobs that ran between AND during timeA and timeB.
Jobs within the timeframe could either:
A: STARTING --> RUNNING --> SUCCESS/FAILURE etc..
B: ... (2 Replies)
Discussion started by: rgilan01
2 Replies
6. Solaris
Hi all,
I encounter some problem with my e1000g interface running on sol 10. I can't permanently change the auto-nego to disable, if i use ndd commands, it will only stay until the next reboot.
But i can't change the link speed either is set to /etc/init.d/nddconfig or using ndd commands.
... (1 Reply)
Discussion started by: mailbox80
1 Replies
7. Solaris
hi frineds
in sunfire 6800 server for one domain when ever i am giving ifconfig -a interface names like hme0,hme1.......are not showing.Actually in the server hme0,hme1,qfe are showing .when i was tried with the cat /etc/path_to_intstshowing tphysical interfcace names .
after giving the... (2 Replies)
Discussion started by: tv.praveenkumar
2 Replies
8. AIX
Hi Admins,
I am having a whole system lpar in open firmware state on HMC.
How can I bring it to running state ?
Let me know. Thanks. (2 Replies)
Discussion started by: snchaudhari2
2 Replies
9. Solaris
on both of my T2000 I am seeing same values of 100Mbps for e1000g0 ethernet port.
i know all four ethernet ports on T2000 are gigabit ports so why is my first link showing as 100Mbps and how can i correct it?
# dladm show-dev
e1000g0 link: up speed: 100 Mbps ... (1 Reply)
Discussion started by: aliyesami
1 Replies
10. Solaris
Hi All,
Please let me know the step by step process to set the e1000g0 interface speed to 1000mbps with full duplex from 100fdx and how to disable the auto negotiation with switch?.
Thanks and Regards,
Ganesh. (7 Replies)
Discussion started by: gsrungav
7 Replies
BE(4) BSD Kernel Interfaces Manual BE(4)
NAME
be -- SPARC Fast Ethernet interface
SYNOPSIS
qec* at sbus? slot ? offset ?
be* at qec?
DESCRIPTION
The be interface provides access to the 10Mb/s and 100Mb/s (half duplex only) Ethernet networks. The be is found on the Sun 10/100 Mbit Eth-
ernet boards (Sun part number SUNW,501-2450).
Each of the host's network addresses is specified at boot time with an SIOCSIFADDR ioctl(2). The be interface employs the address resolution
protocol described in arp(4) to dynamically map between Internet and Ethernet addresses on the local network.
The be is not capable of link autonegotiation, so a media type must be specified with ifconfig(8). The supported media types are:
media 100baseTX
Use 100Mbps, half duplex
media 10baseT
Use 10Mbps, half duplex
SEE ALSO
arp(4), ifmedia(4), inet(4), intro(4), netintro(4), sbus(4), ifconfig(8)
HISTORY
Support for the be first appeared in NetBSD 1.4.
BSD
March 31, 2004 BSD