07-15-2011
a-HA. I think you're right. Just checked the HCL and I do not see our SCSI card listed.
Guess I'll go sift through the rubbage heap to see if I can find one that is.
Thanks!
8 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I'm trying to install a tape drive on a compaq SCO OS 505. well I have gone through the mkdev tape comands and what have you yet no luck. when I reboot and do a simple tape rewind it gives me an error no such device etc.etc. IS there a diference in the xct0 and rct0 a the default?
help.. (2 Replies)
Discussion started by: kikkin
2 Replies
2. Linux
Hello. I have Redhat 8.0 on a laptop. Working good.
I wanted to install the tape drive that is physically attached to it. The tape drive worked fine under Windows98SE. It's one of those parallel QIC-80 drives and I confirmed that it is supported by FTape. It appears that FTape might already... (0 Replies)
Discussion started by: RuralTurtle
0 Replies
3. UNIX for Dummies Questions & Answers
Hi,
I need to restore my tape backup, when I type "tape status" it gives;
status : ready beginning-of-tape write-protected
soft errors : 0
hard errors : 0
underruns : 3
but... (4 Replies)
Discussion started by: alisevA3
4 Replies
4. AIX
I have tape drive in one Lpar. when i saw that time tape is in defined state. After that i deleted the tape drive using the rmdev -R command. Then fired the cfgmgr -v command. But I am not getting the tape drive. Now the drive is even not in defined state also. It is not shown the tape drive. How... (1 Reply)
Discussion started by: pernasivam
1 Replies
5. SCO
Dear All,
I have a tape drive which has worked for offer 3yrs properly on SCO Openserver Release = 3.2v5.0.5. I tried to clean it all invain. I did a fresh installation of unix of the same OS and did the configuration still didn't bear fruits. The tape is a scsi and the configuration is as... (4 Replies)
Discussion started by: njoroge
4 Replies
6. SCO
I've recently been tasked with "refurbishing" an HP Proliant ML370 running SCO 5.0...something. This is primarily used for legacy support and is kept on a shelf for safe keeping. The scope of work includes hardware diagnostics and blowing the dust out.
I have run HP diagnostics on the array,... (1 Reply)
Discussion started by: v1corp
1 Replies
7. UNIX for Dummies Questions & Answers
Hi,
Using Redhat 5.7. I have Quantum tape drive connected to the server. I am trying to install the Netbackup software. Just wondering how can I see the Quantum is connected to the server. is any command I run to see the tape drive is connected?
I used to work on Solaris, I used to do... (1 Reply)
Discussion started by: samnyc
1 Replies
8. HP-UX
I have used ioscan -fnC tape and the system identified the tape drive. what is the command to show a listing of what is on the tape? I have used ls /dev/rmt/rmt0 to no avail. can anyone help?
Thanks in advance (10 Replies)
Discussion started by: Randydog
10 Replies
LEARN ABOUT REDHAT
sane-find-scanner
sane-find-scanner(1) General Commands Manual sane-find-scanner(1)
NAME
sane-find-scanner - find SCSI and USB scanners and their device files
SYNOPSIS
sane-find-scanner [-h|-?] [-v] [-q] [-f] [devname]
DESCRIPTION
sane-find-scanner is a command-line tool to find SCSI and some USB scanners and determine their Unix device files. It's part of the sane-
backends package.
For SCSI scanners, it checks the default generic SCSI device files (e.g., /dev/sg0) and /dev/scanner. The test is done by sending a SCSI
inquiry command and looking for a device type of "scanner" or "processor" (some old HP scanners seem to send "processor"). So sane-find-
scanner will find any SCSI scanner connected to those default device files even if it isn't supported by any SANE backend.
For USB scanners, first the USB kernel scanner device files (e.g. /dev/usb/scanner0), /dev/usb/scanner, and /dev/usbscanner are tested. The
files are opened and the vendor and device ids are determined if the operating system supports this feature. Currently USB scanners are
only found this way if they are supported by the Linux scanner module or the FreeBSD or OpenBSD uscanner driver. After that test, sane-
find-scanner tries to scan for USB devices found by the USB library libusb (if available). There is no special USB class for scanners, so
the heuristics used to distinguish scanners from other USB devices is not perfect. sane-find-scanner will even find USB scanners, that are
not supported by any SANE backend.
sane-find-scanner won't find parallel port scanners, or scanners connected to proprietary ports.
OPTIONS
-h, -? Prints a short usage message.
-v Verbose output. If used once, sane-find-scanner shows every device name and the test result. If used twice, SCSI inquiry informa-
tion and the USB device descriptors are also printed.
-q Be quiet. Print only the devices, no comments.
-f Force opening all explicitely given devices as SCSI and USB devices. That's useful if sane-find-scanner is wrong in determing the
device type.
devname Test device file "devname". No other devices are checked if devname is given.
EXAMPLE
sane-find-scanner -v
Check all SCSI and USB devices for available scanners and print a line for every device file.
sane-find-scanner /dev/scanner
Look for a (SCSI) scanner only at /dev/scanner and print the result.
SEE ALSO
sane(7), sane-scsi(5), sane-usb(5), scanimage(1), xscanimage(1), xsane(1), sane-"backendname"(5)
AUTHOR
Oliver Rauch, Henning Meier-Geinitz and others
SUPPORTED PLATFORMS
USB support is limited to Linux (kernel, libusb), FreeBSD (kernel, libusb), NetBSD (libusb), OpenBSD (kernel, libusb). Detecting the vendor
and device ids only works with Linux or libusb.
SCSI support is available on Irix, EMX, Linux, Next, AIX, Solaris, FreeBSD, NetBSD, OpenBSD, and HP-UX.
BUGS
No support for parallel port scanners yet.
15 Sep 2002 sane-find-scanner(1)