11-29-2010
NIC card issue
well,
thank you for reply
but i need on solaris not for Aix
please give steps for Solaris operating system
\thank you again in advance
10 More Discussions You Might Find Interesting
1. Solaris
Hi,
We have a 4 port Sun gigaswift NIC card on our sun fire server.
If the card is a physical one I know how to check the settings/speed. But since this is a virtual card with 4 ports , I am not sure as how we can check the settings.
Details
-----------
root:/> ifconfig -a
lo0:... (3 Replies)
Discussion started by: pray44u
3 Replies
2. Solaris
Is there a way to check if my Sun box's network interface card is set to 10 or 100 Mbps?
Thanks! (1 Reply)
Discussion started by: FredSmith
1 Replies
3. UNIX for Dummies Questions & Answers
I am a beginer in unix .
I would like to know what is the command in orser to change NIC and Device NO (1 Reply)
Discussion started by: Ilias Kappatos
1 Replies
4. IP Networking
I have a TOSHIBA AS7000 B150 Sun Box
I wanted to run it with 100M/full duplex
I had added this to the /etc/system file to make to setting permenant So it would be set correctly on reboot.
set eri:eri_adv_100fdx_cap=1
set eri:eri_adv_100hdx_cap=0
set eri:eri_adv_autoneg_cap=0
But when I... (4 Replies)
Discussion started by: AirWalker83
4 Replies
5. Solaris
I recently learned that Sun Solaris network cards (ce devices) have problems with ndd -get commands. I did some searching and found out about the netstat -k command to show me the link speed. What is the best way to change the link speed (both one time and permanently)?
I am running Solaris 9... (7 Replies)
Discussion started by: hshapiro
7 Replies
6. Linux
Hi,
I would like to know how to change the speed of ethernet card in linux? as it is showing auto-neg using mii-tool -v eth0
and my requirement is 100mbps full duplex.
Regards,
Manoj (3 Replies)
Discussion started by: manoj.solaris
3 Replies
7. AIX
How to change Speed Duplex !
How to change Speed Duplex by command
chdev -P -l ent1 -a media_speed=1000_Full_Duplex
How to change Speed Duplex by Smitty .
smitty chgenet -> select adapter -> change Media speed etc. -> set "Apply change to DATABASE only" to yes -> Enter -> ... (0 Replies)
Discussion started by: ITHelper
0 Replies
8. UNIX for Advanced & Expert Users
Hi,
Does anyone know how can I determine the maximum capable speed on a network interface card for different OS like HP, Sun, AIX and Linux.
I am aware of the tool "ethtool" which can be used for Linux. Are there any handly commands or /proc files where I can get this info depending on the OS.... (3 Replies)
Discussion started by: devtakh
3 Replies
9. Solaris
Hi,
I have few Solaris (9 and 10) servers, whose consoles are running on 10 MBPs. Now, Network team is changing their switch, which doesn't support 10 MBPs and we need to check if console all of those servers will support 100MBPs or more.
Is there any way to check supported (or maximum supported)... (7 Replies)
Discussion started by: solaris_1977
7 Replies
10. Red Hat
Hi,
I would like to know how to find out ACTUAL speed of NIC Card.
I have used the command ethtool eth0, it is showing supported modes,
but what is acutal speed ? how to find out? (4 Replies)
Discussion started by: manoj.solaris
4 Replies
BNX(4) BSD Kernel Interfaces Manual BNX(4)
NAME
bnx -- Broadcom NetXtreme II 10/100/1000 Ethernet device
SYNOPSIS
bnx* at pci?
brgphy* at mii?
DESCRIPTION
The bnx driver supports Broadcom's NetXtreme II product family, such as the BCM5706 PCI-X and BCM5708-BCM5709 PCI Express Ethernet con-
trollers, which includes the following:
o Dell PowerEdge 1950 integrated BCM5708 NIC (10/100/1000baseT)
o Dell PowerEdge 2950 integrated BCM5708 NIC (10/100/1000baseT)
o Dell PowerEdge M710 integrated BCM5709S NIC (1000baseSX)
o HP NC370F PCI-X Multifunction Gigabit server adapter (1000baseSX)
o HP NC370T PCI-X Multifunction Gigabit server adapter (10/100/1000baseT)
o HP NC373F PCI Express Multifunction Gigabit server adapter (1000baseSX)
o HP NC373i PCI Express Multifunction Gigabit embedded server adapter (10/100/1000baseT)
o HP NC380T PCI Express Dual Port Multifunction Gigabit server adapter (10/100/1000baseT)
o IBM xSeries 3550 integrated BCM5708 NIC (10/100/1000baseT)
o IBM xSeries 3650 integrated BCM5708 NIC (10/100/1000baseT)
The NetXtreme II product family is composed of various Converged NIC (or CNIC) Ethernet controllers which support a TCP Offload Engine (TOE),
Remote DMA (RDMA), and iSCSI acceleration, in addition to standard L2 Ethernet traffic, all on the same controller. The following features
are supported in the bnx driver under NetBSD:
IPv4 receive IP/TCP/UDP checksum offload
Jumbo frames (up to 9022 bytes)
VLAN tag insertion
Interrupt coalescing
10/100/1000Mbps operation in full-duplex mode
10/100Mbps operation in half-duplex mode
The bnx driver supports the following media types:
autoselect Enable autoselection of the media type and options. The user can manually override the autoselected mode via ifconfig(8).
10baseT/UTP Set 10Mbps operation. The ifconfig(8) mediaopt option can also be used to select either full-duplex or half-duplex modes.
100baseTX Set 100Mbps (Fast Ethernet) operation. The ifconfig(8) mediaopt option can also be used to select either full-duplex or
half-duplex modes.
1000baseTX Set 1000baseTX operation over twisted pair. Only full-duplex mode is supported.
1000baseSX Set 1000Mbps (Gigabit Ethernet) operation. Both full-duplex and half-duplex modes are supported.
2500baseSX Set 2500Mbps operation. Only full-duplex mode is supported.
The bnx driver supports the following media options:
full-duplex Force full duplex operation.
half-duplex Force half duplex operation.
For more information on configuring this device, see ifconfig(8).
SEE ALSO
arp(4), brgphy(4), ifmedia(4), intro(4), mii(4), netintro(4), pci(4), ifconfig(8)
HISTORY
The bnx device driver first appeared in NetBSD 4.0.
BSD
December 10, 2010 BSD