|
|
Sponsored Content
Special Forums
Hardware
Slackware 13.1 can't configure two network cards
Post 302447935 by Corona688 on Tuesday 24th of August 2010 06:01:30 PM
08-24-2010
|
|
10 More Discussions You Might Find Interesting
1. UNIX Desktop Questions & Answers
I am using Slackware 7 on my IBM Thinkpad. I am unable to configure it to display a graphical environment. Typing startx usually generates a few errors. The system, however, does boot into the shell environment without any issues or problems. I have been able to setup Slackware 7 successfully... (2 Replies)
Discussion started by: adrienb
2 Replies
2. UNIX for Dummies Questions & Answers
Our shops server runs SCO Openserver 5 release 5. It has two network cards in it (one on 10.0.0.6 and one on 90.0.0.99). When I run scoadmin and look at the network settings it show both my 3com network cards and a loop back driver http://theentertainer.com/james/untitled.jpg
Can anyone tell... (1 Reply)
Discussion started by: potter
1 Replies
3. Solaris
Hi,
I'm looking for a command to be able to disable a network card under the boot PROM.
I need it to force my Jumpstart to use the Ethernet card of my server (V880) instead of my fiber card (gem0).
Thanks,
Fabien (6 Replies)
Discussion started by: unclefab
6 Replies
4. Solaris
Hi,
I'm looking for a command to be able to list all my network cards available on my server.
With the command "ifconfig - a", I can only see to configured network card(s)
Any idea ? :confused:
Thanks a lot for your help,
Fabien (5 Replies)
Discussion started by: unclefab
5 Replies
5. AIX
The title speaks for itself. I have never attempted this but understand there is a way to use two network cards (en0 and en1) with the same IP address so as to load balance the traffic flow through both cards. Anyone know the answer? (4 Replies)
Discussion started by: johnf
4 Replies
6. Solaris
Hi all,
I have a server running with Solaris and I have 2 Pci cards installed on this server (since a while), 1 with 4 coppers connections output and one with a Fiber network connection output.
Today, this server is using the on board network connection (Ce0).
How can I find the other... (7 Replies)
Discussion started by: unclefab
7 Replies
7. Solaris
Hi All,
Hope you are all doing good.
In MY unix box i have 2 network cards. I want to know what if one network card fails. Does the second one will automatically take all the traffic or how it is supposed to work. Also in my logs i am seeing below errors . Can you throw some light of this qfe... (3 Replies)
Discussion started by: Krrishv
3 Replies
8. Solaris
Hi all
I hate networking, I hate everything to do with it. Its something I do in anger in one contract, then forget. This is more of a question / than a problem.
So, on a solaris 10 server, using older qfe cards, Ive got a sun truck with 4 nics (qfe0,3,4,7), and a ipmp pair (hemo0,qfe1).... (2 Replies)
Discussion started by: sbk1972
2 Replies
9. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
10. Slackware
How configure micromax bsnl 3G modem in KPPP on slackware 13.1 while it automatically mounted under
/dev/sr1 iso9660 /media/modem
and in lsusb command add following information:
Bus 001 Device 020: ID 1c9e:f000
now i follow these steps for usb switch to modem
usb_modeswitch.conf ... (0 Replies)
Discussion started by: hitlar
0 Replies
LEARN ABOUT NETBSD
ne
NE(4) BSD Kernel Interfaces Manual NE(4) NAME
ne -- NE2000 and compatible Ethernet cards device driver SYNOPSIS
ISA boards ne0 at isa? port 0x280 irq 9 ne1 at isa? port 0x300 irq 10 ne* at isapnp? MCA boards ne* at mca? slot ? PCI boards ne* at pci? dev ? function ? PCMCIA ne* at pcmcia? function ? acorn32 ne* at podulebus? amiga ne* at zbus0 # AriadneII, X-surf amigappc ne* at zbus0 # AriadneII, X-surf atari ne0 at mainbus0 # EtherNEC on Atari ROM cartridge slot evbarm ne0 at obio? addr 0x0e000200 intr 5 # on-board Asix AX88796 evbsh3 ne0 at mainbus? # Realtek RTL8019AS x68k ne* at intio0 addr 0xece300 intr 249 # Nereid Ethernet ne* at intio0 addr 0xeceb00 intr 248 # Nereid Ethernet neptune0 at intio0 addr 0xece000 intr 249 # Neptune-X neptune1 at intio0 addr 0xece400 intr 249 # Neptune-X at alt. addr. ne* at neptune? addr 0x300 DESCRIPTION
The ne device driver supports NE2000 and compatible (including NE1000) Ethernet cards. While the original NE2000 is designed for ISA bus, the compatible Realtek 8019 chip is widely used on various local busses and ne driver also supports such devices on various machines. MEDIA SELECTION
The Realtek 8019 (ISA, ISAPnP, some PCMCIA) and Realtek 8029 (PCI) NE2000-compatible Ethernet chips include support for software media selec- tion. If one of these chips is detected by the driver, the list of supported media will be displayed. For all other chips supported by the ne driver, media selection must be performed either via card jumper settings or by vendor-supplied con- figuration programs. DIAGNOSTICS
ne0: where did the card go? The driver found the card, but was unable to make the card respond to complete the configuration sequence. SEE ALSO
ifmedia(4), intro(4), isa(4), isapnp(4), mca(4), pci(4), pcmcia(4), ifconfig(8) BSD
April 3, 2010 BSD