Visit Our UNIX and Linux User Community


Modem


 
Thread Tools Search this Thread
Top Forums UNIX for Dummies Questions & Answers Modem
# 1  
Old 07-09-2002
Network Modem

Pleaseee... Helpppp.... !!!

I am using SCO Open Server 5.05. Recently, i have upgraded the system which means transfer all apps and data to the new system. Everything work well except one thing. On my old system i have an external modem which to dial out. Now that i use the same modem on the new system which doesn't seems to work..... Everytime i tried to dial out.... All i got is " CAN NOT OPEN MODEM ". What could be the problem ? And how should I correct this problem... Pleaseee Helpppp....

Thank you so much for you time
# 2  
Old 07-09-2002
Don't know if this will help or not - pcunix.com SCO modem
# 3  
Old 07-09-2002
Or even better - SCO - how to set up a modem
# 4  
Old 07-09-2002
Cannot open modem.. Is the Modem connected on your machine ? is it On ? Any messages or error code during bootup ? Also state what modem are you using.
# 5  
Old 07-11-2002
Modem

Hi... Thanks for all your help!
I have found the problem. Modem has conflict address. What i did was, i went into CMOS setup and change serial port from IRQ4 to IRQ3 and voala..... The modem is working fine now.

Again, thank you for all your help.
 

Previous Thread | Next Thread
Test Your Knowledge in Computers #396
Difficulty: Medium
HP-UX was the first Unix to offer access control lists for file access permissions as an alternative to the standard Unix permissions system.
True or False?

10 More Discussions You Might Find Interesting

1. IP Networking

modem detection

How to get information that where is my modem configured in /dev. I have two modems configured in my device .. one is USB and other is PCI modem.. USB is detected as /dev/USB0. but how to see about PCI modem? (0 Replies)
Discussion started by: s123.radha
0 Replies

2. Solaris

Modem

hi folks, i am looking for a analog modem to use it with a solaris9 sparc mashine. as far as i know, solaris communicates with the modem using AT-commands. so do i need a special modem for solaris or just a modem? i am open for everything. PCI-modem, seriell modem, usb modem. what are you using? i... (1 Reply)
Discussion started by: pressy
1 Replies

3. Solaris

Is the cable you are using a null modem cable or a modem cable

Hi all, Is there any difference between a null modem cable or a modem cable ? i assume that a null modem cable is a normal cable that i used from cpu serial ports to a modem for dialup. please correct if i am wrong, thks (2 Replies)
Discussion started by: waterbear
2 Replies

4. UNIX for Dummies Questions & Answers

Dial-Up Modem

Im using Kinternet with a Lucent modem on Suse 9.0 Ive installed the ltmodem driver and suse says the device is ready and configured. Ive configured it at /dev/ttyS0 This is the log that Kinternet gives after trying to connect: SuSE Meta pppd (smpppd-ifcfg), Version 1.06 on linux. Status... (0 Replies)
Discussion started by: Synbios
0 Replies

5. UNIX for Dummies Questions & Answers

Modem - Test /dev/modem

Ok. I tried following the directions from some of the other threads, but I've hit a road block. I have red hat 7.3 and I installed the hcf package: hcfpcimodem-0.99lnxtbeta03042700k2.4.18_3-1rh.i386.rpm It installed ok, no errors, but I still can't get linux to find my modem. I've tried... (2 Replies)
Discussion started by: lawadm1
2 Replies

6. UNIX for Dummies Questions & Answers

modem

I have got Suse 8.0 by using a modem (US Robotics 56K Faxmodem Ext). During connection i got the error 16. I tried it under RedHat and Mandrake too.....same problem. What can i do ? Thanx...a lot... Logfile: SuSE Meta pppd (smpppd), Version 0.73 on zuhause. wwwoffle not is running ... (1 Reply)
Discussion started by: Pennywize
1 Replies

7. UNIX for Dummies Questions & Answers

Modem Volume

Specs: Dlink DFE-560EL external modem. RedHat 7.1 How do you turn off the modem volume? I am getting annoyed of it beeping everytime I use it but there is no switch on the hardware to tune down the volume. I have tried using minicom and use the following commands: ATL0 ATM0 Next, I... (2 Replies)
Discussion started by: arz
2 Replies

8. UNIX for Dummies Questions & Answers

Modem problem: "Sorry, modem is busy"

Hi! I have a little prob with dialing up to the internet... When I try connect, it says "Sorry, modem is busy"... Specs: Laptop 56K modem Slackware 8.0 Kernel 2.4.5 Cheers;) (4 Replies)
Discussion started by: satan404
4 Replies

9. UNIX for Advanced & Expert Users

Modem

I've spent enough time trying to put on work Lucent Winmodem in my armada M300 (compaq laptop) I use Mandrake 8.0 but as soon as i get connected and prompmts appears modem shutsdown. Does any one had a similar situation, solved it? cheers (2 Replies)
Discussion started by: alex blanco
2 Replies

10. UNIX for Dummies Questions & Answers

Modem on HP-UX 10.20

Hi everyone I am having some real difficulties getting a dial in modem to work on one of my HP boxes. It's a mux modem on port 7 which I have set up at 9600 baud. I can dial in, the handshakes are completed, but then it returns incoherent characters on the emulation screen. I think my dial in... (1 Reply)
Discussion started by: alwayslearningunix
1 Replies

Featured Tech Videos