07-09-2002
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi everyone
I am having some real difficulties getting a dial in modem to work on one of my HP boxes. It's a mux modem on port 7 which I have set up at 9600 baud.
I can dial in, the handshakes are completed, but then it returns incoherent characters on the emulation screen. I think my dial in... (1 Reply)
Discussion started by: alwayslearningunix
1 Replies
2. UNIX for Advanced & Expert Users
I've spent enough time trying to put on work Lucent Winmodem in my armada M300 (compaq laptop) I use Mandrake 8.0 but as soon as i get connected
and prompmts appears modem shutsdown.
Does any one had a similar situation, solved it?
cheers (2 Replies)
Discussion started by: alex blanco
2 Replies
3. UNIX for Dummies Questions & Answers
Hi!
I have a little prob with dialing up to the internet... When I try connect, it says "Sorry, modem is busy"...
Specs:
Laptop
56K modem
Slackware 8.0
Kernel 2.4.5
Cheers;) (4 Replies)
Discussion started by: satan404
4 Replies
4. UNIX for Dummies Questions & Answers
Specs:
Dlink DFE-560EL external modem.
RedHat 7.1
How do you turn off the modem volume? I am getting annoyed of it beeping everytime I use it but there is no switch on the hardware to tune down the volume.
I have tried using minicom and use the following commands:
ATL0
ATM0
Next, I... (2 Replies)
Discussion started by: arz
2 Replies
5. UNIX for Dummies Questions & Answers
I have got Suse 8.0 by using a modem (US Robotics 56K Faxmodem Ext).
During connection i got the error 16. I tried it under RedHat and Mandrake too.....same problem. What can i do ?
Thanx...a lot...
Logfile:
SuSE Meta pppd (smpppd), Version 0.73 on zuhause.
wwwoffle not is running ... (1 Reply)
Discussion started by: Pennywize
1 Replies
6. UNIX for Dummies Questions & Answers
Ok. I tried following the directions from some of the other threads, but I've hit a road block.
I have red hat 7.3 and I installed the hcf package:
hcfpcimodem-0.99lnxtbeta03042700k2.4.18_3-1rh.i386.rpm
It installed ok, no errors, but I still can't get linux to find my modem. I've tried... (2 Replies)
Discussion started by: lawadm1
2 Replies
7. UNIX for Dummies Questions & Answers
Im using Kinternet with a Lucent modem on Suse 9.0
Ive installed the ltmodem driver and suse says the device is ready and configured. Ive configured it at /dev/ttyS0
This is the log that Kinternet gives after trying to connect:
SuSE Meta pppd (smpppd-ifcfg), Version 1.06 on linux.
Status... (0 Replies)
Discussion started by: Synbios
0 Replies
8. Solaris
Hi all,
Is there any difference between a null modem cable or a modem cable ?
i assume that a null modem cable is a normal cable that i used from cpu serial ports to a modem for dialup.
please correct if i am wrong,
thks (2 Replies)
Discussion started by: waterbear
2 Replies
9. Solaris
hi folks,
i am looking for a analog modem to use it with a solaris9 sparc mashine. as far as i know, solaris communicates with the modem using AT-commands. so do i need a special modem for solaris or just a modem? i am open for everything. PCI-modem, seriell modem, usb modem. what are you using? i... (1 Reply)
Discussion started by: pressy
1 Replies
10. IP Networking
How to get information that where is my modem configured in /dev.
I have two modems configured in my device .. one is USB and other is PCI modem.. USB is detected as /dev/USB0. but how to see about PCI modem? (0 Replies)
Discussion started by: s123.radha
0 Replies
LEARN ABOUT PHP
httppower
httppower(8) powerman httppower(8)
NAME
httppower - communicate with HTTP based power distribution units
SYNOPSIS
httppower [--url URL]
DESCRIPTION
httppower is a helper program for powerman which enables it to communicate with HTTP based power distribution units. It is run interac-
tively by the powerman daemon.
OPTIONS
-u, --url URL
Set the base URL.
INTERACTIVE COMMANDS
The following commands are accepted at the httppower> prompt:
auth user:pass
Authenticate to the base URL with specified user and password, using ``basic'' HTTP authentication which sends the user and password
over the network in plain text.
seturl URL
Set the base URL. Overrides the command line option.
get [URL-suffix]
Send an HTTP GET to the base URL with the optional URL-suffix appended.
post [URL-suffix] key=val[&key=val]...
Send an HTTP POST to the base URL with the optional URL-suffix appended, and key-value pairs as argument.
FILES
/usr/sbin/httppower
/etc/powerman/powerman.conf
ORIGIN
PowerMan was originally developed by Andrew Uselton on LLNL's Linux clusters. This software is open source and distributed under the terms
of the GNU GPL.
SEE ALSO
powerman(1), powermand(8), httppower(8), plmpower(8), vpcd(8), powerman.conf(5), powerman.dev(5), powerman-devices(7).
http://sourceforge.net/projects/powerman
powerman-2.3.5 2009-02-09 httppower(8)