9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
2. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
3. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
4. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
5. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
6. Solaris
HI,
genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
genunix: WARNING: ce0: fault detected external to device; service degraded
genunix: WARNING: ce0: xcvr addr:0x01 - link down
genunix: NOTICE: ce0: fault cleared external to device; service available
genunix: ... (4 Replies)
Discussion started by: sunnybee
4 Replies
7. UNIX for Advanced & Expert Users
Hi all,
I'm using an HP Proliant server with double NIC and Debian 5 (Lenny) as its OS. I used link bonding on it for several years with no problem.
Today, (now only one interface connected to switch) the interface went down. I restarted networking service (/etc/init.d/networking restart) and... (7 Replies)
Discussion started by: mjdousti
7 Replies
8. AIX
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies
9. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
VLAN(4) BSD Kernel Interfaces Manual VLAN(4)
NAME
vlan -- IEEE 802.1Q Virtual LAN network device
SYNOPSIS
pseudo-device vlan
DESCRIPTION
The vlan interface provides support for IEEE 802.1Q Virtual Local Area Networks (VLAN). This supports the trunking of more than one network
on a single network interface. This is particularly useful on routers or on hosts which must be connected to many different networks through
a single physical interface.
To use a vlan interface, the administrator must first create the interface and then specify the VID (VLAN identifier, the first 12 bits from
a 16-bit integer which distinguishes each VLAN from any others) and physical interface associated with the VLAN. This can be done by using
the ifconfig(8) create, vlan, and vlanif subcommands from a shell command line or script. From within a C program, use the ioctl(2) system
call with the SIOCSIFCREATE and SIOCSIFVLAN arguments.
To be compatible with other IEEE 802.1Q devices, the vlan interface supports a 1500 byte MTU, which means that the parent interface will have
to handle packets that are 4 bytes larger than the original Ethernet standard. Drivers supporting this increased MTU are:
- drivers using the DP8390 core (such as ec(4), ne(4), we(4), and possibly others)
- bge(4)
- bnx(4)
- ea(4)
- eb(4)
- epic(4)
- etherip(4)
- ex(4)
- fxp(4)
- gem(4)
- hme(4)
- le(4)
- sip(4)
- ste(4)
- stge(4)
- ti(4)
- tl(4)
- tlp(4)
- vge(4)
- vr(4)
- wm(4)
- xi(4)
vlan can be used with devices not supporting the IEEE 802.1Q MTU, but then the MTU of the vlan interface will be 4 bytes too small and will
not interoperate properly with other IEEE 802.1Q devices, unless the MTU of the other hosts on the VLAN are also lowered to match.
EXAMPLES
The following will create interface vlan0 with VID six, on the Ethernet interface tlp0:
ifconfig vlan0 create
ifconfig vlan0 vlan 6 vlanif tlp0
After this set up, IP addresses (and/or other protocols) can be assigned to the vlan0 interface. All other hosts on the Ethernet connected
to tlp0 which configure a VLAN and use VID six will see all traffic transmitted through vlan0.
The same VLAN can be created at system startup time by placing the following in /etc/ifconfig.vlan0:
create
vlan 6 vlanif tlp0
SEE ALSO
ifconfig(8)
HISTORY
The vlan device first appeared in NetBSD 1.5.1, and was derived from a VLAN implementation that appeared in FreeBSD and OpenBSD.
BUGS
The vlan interfaces do not currently inherit changes made to the physical interfaces' MTU.
BSD
December 16, 2010 BSD