How to identifying the network card ?

10 More Discussions You Might Find Interesting

1. Red Hat

Regarding Network Interface Card

Dear All , While taking backups in one Linux Server , we find one alert came with regard to Network Interface Card. Pl find the below alert. Network Interface Card performance for NIC:eth1 has exceeded Major threshold. Bytes sent and received per second (Average)= 105540.303101...

2. Hardware

Identifying Network Ports

OK, so I have a real dumb question, but I am desperate for an answer. If my Sun machine shows the following out put. root@xxxx:/# egrep network /etc/path_to_inst "/pci@1f,0/pci@1,1/network@c,1" 0 "eri" "/pci@1f,0/pci@1,1/network@5,1" 1 "eri" Does that indicate that there is one eri...

3. UNIX for Dummies Questions & Answers

How to install a network card

Hey guys, Sorry, this question might look stupid but I have no idea how to install a network card. My server is a Dell PowerEdge T105 with Debian 5.0 Lenny. My network card is a Broadcom NetXtreme BCM5722 Gigabit Ethernet PCI Express. I've plugged the card innside my server and I can see...

4. UNIX for Dummies Questions & Answers

How can I tell which network card is which?

I have three network cards in my unix box. I need to figure out which card corresponds to an assigned IP address. If there some command in unix I can use to make an ethernet interface blink? Any advice would be appreciated.

5. UNIX for Dummies Questions & Answers

Network card and internet

Hi!. I have problems installing my network card under ther redhat kernel. First i tryed my integrated intel pro set 10/100 then my d-link 530tx Pci but none of them seems to be found. also i huse my network card to connect to the net trough PPPOE where i need to type my username and...

6. UNIX for Advanced & Expert Users

network card problem

hi, everyone: alpha 600 au true64 Unix 4.0f my network cart is set "Auto-Negotiate".After operate system startup,the network will be disconnected by itself at sometime. I found some prompt in /usr/adm/messages. "tu0 :transmit FIFO underflow:threshold raised to :256 byte��link up...

7. UNIX for Advanced & Expert Users

Network Card Help

I have been having trouble with my sis900 neytwork card in slacwkare linux. I tried to modprobe the sis900, it didnt give me any errors but it didnt load it. so I put in a realtek 8139 network card and tried it too. These are the errors i get with the two cards when trying to do insmod on either of...

8. IP Networking

Network Card with SGI

The Octane is driving me nuts . It was sitting on the network doing its job nicely and i had to pull the n/w cable out from the wall to pull it from the inside of the table and connected it again . The logs show this -- link down .... < when i pulled it out > link ok < when i connected > But...

9. UNIX for Dummies Questions & Answers

Installing network card

1) i am trying to install realtek network card in caldrea linux, but i am not able to find the interface, 2)i download drivers for network card and i am not able to read the floopy in linux, pls help me out.

10. IP Networking

network card

I have a UnixWare 2 server that has an ISA 3Com NIC that has just a BNC connector on it. I want to remove this and install an ISA 3Com NIC that has a BNC/RJ45 connector. What steps do I have to go through to successfully complete this? Thye are almost the exact same cards except for the...

LEARN ABOUT NETBSD

cnw

CNW(4)							   BSD Kernel Interfaces Manual 						    CNW(4)

NAME

     cnw -- Netwave AirSurfer wireless network driver

SYNOPSIS

     cnw*     at pcmcia? function ?

DESCRIPTION

     The cnw interface provides access to a theoretical 1 Mb/s wireless Ethernet network based on the Netwave AirSurfer Wireless LAN (formerly
     known as the Xircom Netwave Wireless LAN).

     Note that the driver does not support newer devices such as the Netwave AirSurfer ``Plus'', or the BayStack 650/660.  These devices are sup-
     ported by the awi(4) driver.

     Netwave devices are not compatible with IEEE 802.11 wireless networks.  Also note that there are Netwave devices with different wireless fre-
     quency, depending on the radio band plan in each country.

     The card uses 36K of I/O memory mapped to the card.  You may need to increase memory space available to the PCMCIA controller.  See pcmcia(4)
     for details.

     In use, the cards appear to achieve up to a 420Kb/s transfer rate, though a transfer rate between 250Kb/s and 350Kb/s is typical.

     The card operates in the 2.4GHz frequency range and is subject to interference from microwaves, IEEE 802.11 wireless network devices, as well
     as earth.	For example, it seems that IEEE 802.11 channel 14 conflicts with Netwave (US frequency).  They interfere with each other if they
     are both operated in the same geographic region, causing weird packet loss.  You may be able to avoid the interference with IEEE 802.11
     devices, by changing the IEEE 802.11 channel.

HARDWARE

     Cards supported by the cnw driver include:

	   Xircom CreditCard Netwave

	   NetWave AirSurfer

DIAGNOSTICS

     cnw0: can't map memory  Indicates that the driver was not able to allocate enough PCMCIA bus address space into which to map the device.  See
     pcmcia(4) and increase memory available to the PCMCIA controller.

SEE ALSO

     arp(4), awi(4), inet(4), intro(4), pcmcia(4), cnwctl(8)

BSD
								  January 5, 1997							       BSD

Solaris