Haed code nxge0 nic interface with full duplex & 1000mbps

9 More Discussions You Might Find Interesting

1. Solaris

How to Make interface 1000Mbps?

Solaris - 10 Sparc Please suggest to make bnx2 as full duplex with speed 1000 Mbps which is currently at speed 100 Mbps >dladm show-dev e1000g0 link: up speed: 1000 Mbps duplex: full e1000g1 link: unknown speed: 0 Mbps duplex: half e1000g2 ...

2. Solaris

How to find half duplex or full duplex

Hi, How to find whether the server is running with half duplex or full duplex. I tried with the following command ndd -get /dev/ but am not getting any output,. Is the command correct? Also let me know how to change from half to full duplex.

3. Programming

How to modify this c code to get full GUI interface for Unix Linux ?

Hi, the following code comes from Unix Linux dialog utility project. Unfortunately, this project is no more actively maintained. Unix Linux dialog utility is made of widget boxes. One of them is mixedgauge.c In the following example I would like to get rid of flickering when run in...

4. SuSE

configure full duplex

How do I configure full duplex on suse 8.2 I tried ethtool -s eth0 speed 100 duplex full autoneg off the above works but when I reboot the machine the configure was lost. How do I configure full duplex so that when the machine get rebooted the configuration will stay. My interface...

5. IP Networking

NIC speed 100M/full duplex problem

I have a TOSHIBA AS7000 B150 Sun Box I wanted to run it with 100M/full duplex I had added this to the /etc/system file to make to setting permenant So it would be set correctly on reboot. set eri:eri_adv_100fdx_cap=1 set eri:eri_adv_100hdx_cap=0 set eri:eri_adv_autoneg_cap=0 But when I...

6. Solaris

How to force a full duplex

I need to change some Ip addresses for my servers to reflect in the NIS map. I also need to force full duplex on the 10/100 cards & 1/2 duplex in the 10 cards. I can change the IP by doing ifconfig <NIC card > plumb up <newip>. Not quite sure on how to force the full / half duplex & how to...

7. Solaris

change NIC to 1000 Mbps full duplex

Hi all, I tried to use this command ndd -set /dev/eri adv_1000fdx_cap 1 but i get a "operation failed, Invalid argument" anyone can help ? Thanks

8. Programming

full -duplex ?

what is meant by full duplex and half duplex? b'coz in differences b\w hub and switch ,i heard lot this duplex word so please help me

9. UNIX for Dummies Questions & Answers

Full Duplex Howto

Dear Members, I was reading a few posts and saw something about installing two Nics so one could use Full Duplex. I remember back in the day of dial up, you could have two modems and use one for upstream and one for downstream. This was called shotgunning. It seems that you can now do the same...

LEARN ABOUT NETBSD

bnx

BNX(4)							   BSD Kernel Interfaces Manual 						    BNX(4)

NAME

     bnx -- Broadcom NetXtreme II 10/100/1000 Ethernet device

SYNOPSIS

     bnx* at pci?
     brgphy* at mii?

DESCRIPTION

     The bnx driver supports Broadcom's NetXtreme II product family, such as the BCM5706 PCI-X and BCM5708-BCM5709 PCI Express Ethernet con-
     trollers, which includes the following:

     o	 Dell PowerEdge 1950 integrated BCM5708 NIC (10/100/1000baseT)
     o	 Dell PowerEdge 2950 integrated BCM5708 NIC (10/100/1000baseT)
     o	 Dell PowerEdge M710 integrated BCM5709S NIC (1000baseSX)
     o	 HP NC370F PCI-X Multifunction Gigabit server adapter (1000baseSX)
     o	 HP NC370T PCI-X Multifunction Gigabit server adapter (10/100/1000baseT)
     o	 HP NC373F PCI Express Multifunction Gigabit server adapter (1000baseSX)
     o	 HP NC373i PCI Express Multifunction Gigabit embedded server adapter (10/100/1000baseT)
     o	 HP NC380T PCI Express Dual Port Multifunction Gigabit server adapter (10/100/1000baseT)
     o	 IBM xSeries 3550 integrated BCM5708 NIC (10/100/1000baseT)
     o	 IBM xSeries 3650 integrated BCM5708 NIC (10/100/1000baseT)

     The NetXtreme II product family is composed of various Converged NIC (or CNIC) Ethernet controllers which support a TCP Offload Engine (TOE),
     Remote DMA (RDMA), and iSCSI acceleration, in addition to standard L2 Ethernet traffic, all on the same controller.  The following features
     are supported in the bnx driver under NetBSD:

	   IPv4 receive IP/TCP/UDP checksum offload
	   Jumbo frames (up to 9022 bytes)
	   VLAN tag insertion
	   Interrupt coalescing
	   10/100/1000Mbps operation in full-duplex mode
	   10/100Mbps operation in half-duplex mode

     The bnx driver supports the following media types:

     autoselect   Enable autoselection of the media type and options.  The user can manually override the autoselected mode via ifconfig(8).

     10baseT/UTP  Set 10Mbps operation.  The ifconfig(8) mediaopt option can also be used to select either full-duplex or half-duplex modes.

     100baseTX	  Set 100Mbps (Fast Ethernet) operation.  The ifconfig(8) mediaopt option can also be used to select either full-duplex or
		  half-duplex modes.

     1000baseTX   Set 1000baseTX operation over twisted pair.  Only full-duplex mode is supported.

     1000baseSX   Set 1000Mbps (Gigabit Ethernet) operation.  Both full-duplex and half-duplex modes are supported.

     2500baseSX   Set 2500Mbps operation.  Only full-duplex mode is supported.

     The bnx driver supports the following media options:

     full-duplex  Force full duplex operation.

     half-duplex  Force half duplex operation.

     For more information on configuring this device, see ifconfig(8).

SEE ALSO

     arp(4), brgphy(4), ifmedia(4), intro(4), mii(4), netintro(4), pci(4), ifconfig(8)

HISTORY

     The bnx device driver first appeared in NetBSD 4.0.

BSD
								 December 10, 2010							       BSD

Solaris