9 More Discussions You Might Find Interesting
1. Solaris
Solaris - 10 Sparc
Please suggest to make bnx2 as full duplex with speed 1000 Mbps which is currently at speed 100 Mbps
>dladm show-dev
e1000g0 link: up speed: 1000 Mbps duplex: full
e1000g1 link: unknown speed: 0 Mbps duplex: half
e1000g2 ... (2 Replies)
Discussion started by: anand87
2 Replies
2. Solaris
Hi,
How to find whether the server is running with half duplex or full duplex. I tried with the following command ndd -get /dev/ but am not getting any output,. Is the command correct?
Also let me know how to change from half to full duplex. (1 Reply)
Discussion started by: rogerben
1 Replies
3. Programming
Hi,
the following code comes from Unix Linux dialog utility project.
Unfortunately, this project is no more actively maintained.
Unix Linux dialog utility is made of widget boxes.
One of them is mixedgauge.c
In the following example I would like to get rid of flickering
when run in... (0 Replies)
Discussion started by: jack2
0 Replies
4. SuSE
How do I configure full duplex on suse 8.2
I tried
ethtool -s eth0 speed 100 duplex full autoneg off
the above works but when I reboot the machine the configure was lost.
How do I configure full duplex so that when the machine get rebooted the configuration will stay.
My interface... (4 Replies)
Discussion started by: hassan2
4 Replies
5. IP Networking
I have a TOSHIBA AS7000 B150 Sun Box
I wanted to run it with 100M/full duplex
I had added this to the /etc/system file to make to setting permenant So it would be set correctly on reboot.
set eri:eri_adv_100fdx_cap=1
set eri:eri_adv_100hdx_cap=0
set eri:eri_adv_autoneg_cap=0
But when I... (4 Replies)
Discussion started by: AirWalker83
4 Replies
6. Solaris
I need to change some Ip addresses for my servers to reflect in the NIS map.
I also need to force full duplex on the 10/100 cards & 1/2 duplex in the 10 cards.
I can change the IP by doing ifconfig <NIC card > plumb up <newip>.
Not quite sure on how to force the full / half duplex & how to... (2 Replies)
Discussion started by: Remi
2 Replies
7. Solaris
Hi all,
I tried to use this command
ndd -set /dev/eri adv_1000fdx_cap 1
but i get a "operation failed, Invalid argument"
anyone can help ? Thanks (5 Replies)
Discussion started by: DarReNz
5 Replies
8. Programming
what is meant by full duplex and half duplex?
b'coz in differences b\w hub and switch ,i heard lot this duplex word
so please help me (1 Reply)
Discussion started by: parvathy
1 Replies
9. UNIX for Dummies Questions & Answers
Dear Members,
I was reading a few posts and saw something about installing two Nics so one could use Full Duplex. I remember back in the day of dial up, you could have two modems and use one for upstream and one for downstream. This was called shotgunning. It seems that you can now do the same... (4 Replies)
Discussion started by: Phobos
4 Replies
BNX(4) BSD Kernel Interfaces Manual BNX(4)
NAME
bnx -- Broadcom NetXtreme II 10/100/1000 Ethernet device
SYNOPSIS
bnx* at pci?
brgphy* at mii?
DESCRIPTION
The bnx driver supports Broadcom's NetXtreme II product family, such as the BCM5706 PCI-X and BCM5708-BCM5709 PCI Express Ethernet con-
trollers, which includes the following:
o Dell PowerEdge 1950 integrated BCM5708 NIC (10/100/1000baseT)
o Dell PowerEdge 2950 integrated BCM5708 NIC (10/100/1000baseT)
o Dell PowerEdge M710 integrated BCM5709S NIC (1000baseSX)
o HP NC370F PCI-X Multifunction Gigabit server adapter (1000baseSX)
o HP NC370T PCI-X Multifunction Gigabit server adapter (10/100/1000baseT)
o HP NC373F PCI Express Multifunction Gigabit server adapter (1000baseSX)
o HP NC373i PCI Express Multifunction Gigabit embedded server adapter (10/100/1000baseT)
o HP NC380T PCI Express Dual Port Multifunction Gigabit server adapter (10/100/1000baseT)
o IBM xSeries 3550 integrated BCM5708 NIC (10/100/1000baseT)
o IBM xSeries 3650 integrated BCM5708 NIC (10/100/1000baseT)
The NetXtreme II product family is composed of various Converged NIC (or CNIC) Ethernet controllers which support a TCP Offload Engine (TOE),
Remote DMA (RDMA), and iSCSI acceleration, in addition to standard L2 Ethernet traffic, all on the same controller. The following features
are supported in the bnx driver under NetBSD:
IPv4 receive IP/TCP/UDP checksum offload
Jumbo frames (up to 9022 bytes)
VLAN tag insertion
Interrupt coalescing
10/100/1000Mbps operation in full-duplex mode
10/100Mbps operation in half-duplex mode
The bnx driver supports the following media types:
autoselect Enable autoselection of the media type and options. The user can manually override the autoselected mode via ifconfig(8).
10baseT/UTP Set 10Mbps operation. The ifconfig(8) mediaopt option can also be used to select either full-duplex or half-duplex modes.
100baseTX Set 100Mbps (Fast Ethernet) operation. The ifconfig(8) mediaopt option can also be used to select either full-duplex or
half-duplex modes.
1000baseTX Set 1000baseTX operation over twisted pair. Only full-duplex mode is supported.
1000baseSX Set 1000Mbps (Gigabit Ethernet) operation. Both full-duplex and half-duplex modes are supported.
2500baseSX Set 2500Mbps operation. Only full-duplex mode is supported.
The bnx driver supports the following media options:
full-duplex Force full duplex operation.
half-duplex Force half duplex operation.
For more information on configuring this device, see ifconfig(8).
SEE ALSO
arp(4), brgphy(4), ifmedia(4), intro(4), mii(4), netintro(4), pci(4), ifconfig(8)
HISTORY
The bnx device driver first appeared in NetBSD 4.0.
BSD
December 10, 2010 BSD