8 More Discussions You Might Find Interesting
1. Solaris
Hi,
I'm looking to copy a boot disk on an old Solaris 8 system using dd. I'll bring the system down to single user mode and begin from there. I'm copying my source disk to a larger target disk. Do I need to do anything other than the 'dd' command below because the target disk is bigger? ... (2 Replies)
Discussion started by: sparcman
2 Replies
2. HP-UX
Hi,
I wanted to configure new iscsi port on HPUX system, i added the target port address and configured it, once done, went to array side and searched for that host iqn number , but was nt able to find the same, came to host, then when i ran "iscsiutil -pVS" command it gave me below result
... (0 Replies)
Discussion started by: Vinay Kumar D
0 Replies
3. Solaris
Hi all,
OS is Solaros 10 Sparc
While doing Netbackup upgradation to 7.5 , the server was asked to reboot.
But then it came up in single user mode,
and after I typed format command it showed some disk error.
bash-3.00# format
Searching for disks...WARNING:... (2 Replies)
Discussion started by: manalisharmabe
2 Replies
4. Solaris
Hi, I have a firewire external hard drive that I've been using on a Mac but now want to use on my desktop computer that runs on Solaris 10, but when I plug it into the firewire port, nothing happens. I just assumed that it would mount automatically like a USB device but it doesn't. Can someone... (7 Replies)
Discussion started by: Breanne
7 Replies
5. Shell Programming and Scripting
Hello!
I need to write partitioning script wich would work in rescue mode. It will prepare partitions and unpack linux on it. However I need to calculate whole size of the disk and create:
/dev/sda1 --> One big partition (minus (2*size of memory) for swap)
/dev/sda2 --> Swap partition... (1 Reply)
Discussion started by: pug123
1 Replies
6. Solaris
Hi,
I am a newbie to Solaris. I want to know how to find out the controller target and disk number on a SunFire V890 box that has 6X72GB disks. The probe-scsi output is as shown below:
/pci@8,600000/SUNW,qlc@2
LiD HA LUN --- Port WWN --- ----- Disk description -----
0 0 0 ... (1 Reply)
Discussion started by: sudhir_shet
1 Replies
7. UNIX for Dummies Questions & Answers
Hi there!
I received the following error message
The hard disk at channel 2, target 1 had a soft error.
The output of a system check reveiled the following (see entry <2,1> ):
SWXCR xcr0 error counters:
RAID Array 200 Controller Family Information Utility V1.03... (1 Reply)
Discussion started by: Ivo
1 Replies
8. UNIX for Dummies Questions & Answers
Hello All,
I have a laptop running windows 2000 and I have a External Firewire Hard Disk of 60 GB. Now my question is, " Is it possible to install Solaris 8 on this external Firewire Hard Disk". When I tried installing, It did not find the external Firewire Disk, the only partition information,... (1 Reply)
Discussion started by: sanjay92
1 Replies
WREN(3) Library Functions Manual WREN(3)
NAME
wren, ata - hard disk interface
SYNOPSIS
bind #H[drive] /dev
bind #w[target[.lun]] /dev
/dev/hd0disk
/dev/hd0partition
/dev/sd0disk
/dev/sd0partition
...
DESCRIPTION
The hard disk interfaces (wren, #w, is a SCSI disk; ata, #H, is an IDE or ATA disk) serve a one-level directory giving access to the hard
disk partitions. The parameter to attach defines the numerical SCSI target and logical unit number or the IDE drive number to access.
Both default to zero.
Each partition name is prefixed by hd and the numeric drive identifier. The partition always exists and covers the entire disk. The size
of each partition as reported by stat(2) is the number of bytes in the partition, so the size of is the size of the entire disk.
The partition also always exists; it is the last block on the disk for SCSI, second to last for IDE. If it contains valid partition data,
those partitions will be visible as well. Every time the device is bound, the partitions are updated to reflect any changes in the parti-
tion file.
The format of the partition file is the string
plan9 partitions
on a line, followed by partition specifications, one per line, consisting of a name and textual strings for the block start and limit for
each partition on the disk.
The program prep(8) writes the partition table for the disk; its use is preferred to writing it by hand.
SEE ALSO
prep(8), scsi(3)
SOURCE
/sys/src/9/port/devwren.c
/sys/src/9/pc/devata.c
WREN(3)