QE(4) BSD Kernel Interfaces Manual QE(4)NAME
qe -- SPARC Fast Ethernet interface
SYNOPSIS
qec* at sbus? slot ? offset ?
qe* at qec?
DESCRIPTION
The qe interface provides access to 10Mb/s Ethernet networks via the AMD Am79C940 (MACE) Ethernet controller. The qe is found on the Sun
QuadEthernet boards (Sun part number SUNW,501-2062).
Each of the host's network addresses is specified at boot time with an SIOCSIFADDR ioctl(2). The qe interface employs the address resolution
protocol described in arp(4) to dynamically map between Internet and Ethernet addresses on the local network.
SEE ALSO arp(4), be(4), hme(4), ie(4), ifmedia(4), inet(4), intro(4), le(4), netintro(4), qec(4), sbus(4), ifconfig(8)HISTORY
Support for the qe first appeared in NetBSD 1.4.
BSD March 31, 2004 BSD
Check Out this Related Man Page
BE(4) BSD Kernel Interfaces Manual BE(4)NAME
be -- SPARC Fast Ethernet interface
SYNOPSIS
qec* at sbus? slot ? offset ?
be* at qec?
DESCRIPTION
The be interface provides access to the 10Mb/s and 100Mb/s (half duplex only) Ethernet networks. The be is found on the Sun 10/100 Mbit Eth-
ernet boards (Sun part number SUNW,501-2450).
Each of the host's network addresses is specified at boot time with an SIOCSIFADDR ioctl(2). The be interface employs the address resolution
protocol described in arp(4) to dynamically map between Internet and Ethernet addresses on the local network.
The be is not capable of link autonegotiation, so a media type must be specified with ifconfig(8). The supported media types are:
media 100baseTX
Use 100Mbps, half duplex
media 10baseT
Use 10Mbps, half duplex
SEE ALSO arp(4), ifmedia(4), inet(4), intro(4), netintro(4), sbus(4), ifconfig(8)HISTORY
Support for the be first appeared in NetBSD 1.4.
BSD March 31, 2004 BSD
I am trying to find a way to list all the IP addresses/aliases associated with the HP-UX & Sun Solaris boxes in our network. Is there any way to do this without root access? I have no problem checking the known addresses/aliases, but am finding it almost impossible to find unknown... (1 Reply)
We are trying to Establish Network using Linux.Now we are facing the problem in configring Ethernet.In out network we are giving eth0 in server and activating it at the boot time,so it is activating as it is but when we define the Ethernet of node on server and allowing it to activate at boot time... (5 Replies)
Hey. i have been trying to configure the on board Ethernet in My Sparcstation 5, i have spent a lot of time on the ifconfig man pages. but it could really be nice with some pro. help. i don't think the interface is running . i don't know what name the interface have, le0 eth0 et0, it just says no... (4 Replies)
Hi,
I have just installed Sun Solaris 8 on my Sun Server Machine.
I have assigned a one ip to eri0 interface. i want to assign anohter ip to the another ethernet interface but i am not able to find it. can any body help me to assigning the second ip to the second inteface so that i can able to... (11 Replies)
I was checking nettl output for a unstable telnet to my server. this is part of output:
###
***********************************STREAMS/UX*******************************@#%
Timestamp : Sun Jun 22 EETDST 2008 22:14:47.492899
Process ID : Subsystem ... (4 Replies)
Hi All,
I want to configure network into my system.
i tried following in to configure the interface
to find the name of interface
#prtdiag |grep net
i got following
0 PCI-1 33 1 network-SUNW, hme
then i tried following
#prtconf -v |grep net
network, instance #0 (6 Replies)
Hi here is my question;
any help would be appreciated
The Linux system pokey has two Ethernet cards. The first Ethernet card is connected to a companywide
TCP/IP network covering the addresses 87.65.43.xx, where pokey's address is
87.65.43.21. The second Ethernet interface is connected to a... (2 Replies)
I have a new Sun 440 and I am trying to configure it. Non of the Ethernet ports are enabled; when I issue "ifconfig -a" it returns nothing. Is there a way to know the available port name (e.g. ce, bge, etc.) by running a command or so ? (4 Replies)
I just reciently purchased a Sun Ultra 5. I changed the network settings to work with my router (at least thats what I thought I was doing). After I rebooted I keep getting the message "Re-trying host configuration" over and over again.
Since this is during the boot up it never lets me get to... (5 Replies)
Hi All,
In Ultra 10 at time system is not displaying value for Ethernet address and Host ID.
Also, when i am trying to change the value of environment variables i am getting below message and value is not changing
Thanks (4 Replies)
Hi!
I have Sun SPARC Enterprise T5140 with Solaris 10 and it unable to up network interface after boot, but after issuing ifconfig interface begins to work... svcs -xv says that service svc:/network/physical:default is failed to start and service log stores something like "service method... (5 Replies)
This may be a stupid question, but I don't want to take any chances.
I have a Sun T2000 in production. I want to run the "resetsc" command on the ALOM controller to active an IP address change. Will resetting ALOM affect the running OS?
Thanks (2 Replies)
I have problem with my application. Application is running on embedded Linux machine. It's basically multiprotocol gateway that connects two industrial Ethernet networks.
We are experiencing some kind of application hang every 2 to 3 days. It seems like both threads are still running but... (12 Replies)
Hi, I'm trying to find a way to protect my network against arp spoofing.
What it is:
An attacker sends fake arp packets in the network, identifying himself as the router. All network traffic is then redirected to this attacker.
How to protect myself:
In my opinion, the best possible... (2 Replies)
Hi all,
I am using an F5 LTM Load balancer VM. Its network config is as follows:
eth0 Link encap:Ethernet HWaddr 00:50:56:01:01:FA
inet addr:192.168.2.104 Bcast:192.168.2.255 Mask:255.255.255.0
inet6 addr: fe80::250:56ff:fe01:1fa/64 Scope:Link
UP... (3 Replies)