9 More Discussions You Might Find Interesting
1. IP Networking
Hello All,
I have one requirement in which, i have 3 connections one ADSL and two 4G dongle (Jio/Airtel).
Where i need to configure ADSL and 4G connections, which i have configured and able to connect internet throught them,
Now i need to create set-up for failover and fall back between them,... (0 Replies)
Discussion started by: linux.amrit
0 Replies
2. Shell Programming and Scripting
Hello,
First of all, congratulations on this forum! Very mice material!
This is my fist thread and it has to do with connecting to an adsl modem and executing some commands.
Heres what I do:
$username = 'admin';
$passwd = 'admin';
$telnet = new Net::Telnet ( Timeout=>10,... (2 Replies)
Discussion started by: Ravendark
2 Replies
3. Solaris
Hello all,
granted that I am an absolute beginner with Solaris, I'd like to use my adsl modem, t's a Zyxel prestige 630.
I managed to install and configure it under Ubuntu using the drivers from Conexant AccessRunner ADSL USB modems with Linux ; is there a chance to do the same under Solaris 10... (0 Replies)
Discussion started by: clalfa
0 Replies
4. IP Networking
I have RedHat 9.0 installed on three of my servers (PIII - 233MHz) and want that they share a common IP address so that any request made reaches each of the servers.
Can anyone suggest how should I setup my LAN. I'm new to networking in Linux so please elaborate and would be thankful for a timely... (2 Replies)
Discussion started by: Rakesh Ranjan
2 Replies
5. Solaris
Hi,
I have USB Siemens Santis 100 ADSL modem.I need driver for this modem on Solaris 10.Please help me with some info.Platform is x86.Thanks. (2 Replies)
Discussion started by: Upravnik
2 Replies
6. UNIX for Dummies Questions & Answers
Hello, everyone. I have a little favor to ask. Me and my friends decided sharing an ADSL line with four PCs.
PC no.1: Desktop, two netcard (2000 and 8139), Mandrake 9.0
PC no.2: Acer notebook, PC Card, RTL-8139C/8139C+, MS 98 + Win 2000 Pro
PC no.3: Desktop, net card 8139, WindowME + Win 2000... (1 Reply)
Discussion started by: HOUSCOUS
1 Replies
7. UNIX for Dummies Questions & Answers
Hey everyone, just to let you all know "I'm an uber n00b"
I'm connected to Telstra Bigpond's (Australian ISP) ADSL network, now I;m running Darwin 1.41 on an Apple Macintosh PPC computer.
I don't know how to set up ADSL on this system, can someone please guide me. (3 Replies)
Discussion started by: Syphor
3 Replies
8. UNIX for Dummies Questions & Answers
Hi everyone,
This is basically my problem. I setup freebsd, and wanted to get my adsl connection up which uses pppoe to connect. I followed the steps in this (http://free.mine.nu/~squirrel/PPPoE/FreeBSD%20PPPoE%20Howto.htm) manual and configured everything successfully. The problem begins when i... (7 Replies)
Discussion started by: Luftwaffe
7 Replies
9. IP Networking
Is ADSL support available for Unix/Linux? If I want to set up a internet server, will it have to be Windows with a seperate unix box? Or can it be a clean unix server? (2 Replies)
Discussion started by: vannie
2 Replies
GRE(4) BSD Kernel Interfaces Manual GRE(4)
NAME
gre -- encapsulating network device
SYNOPSIS
To compile the driver into the kernel, place the following line in the kernel configuration file:
device gre
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_gre_load="YES"
DESCRIPTION
The gre network interface pseudo device encapsulates datagrams into IP. These encapsulated datagrams are routed to a destination host, where
they are decapsulated and further routed to their final destination. The ``tunnel'' appears to the inner datagrams as one hop.
gre interfaces are dynamically created and destroyed with the ifconfig(8) create and destroy subcommands.
This driver corresponds to RFC 2784. Encapsulated datagrams are prepended an outer datagram and a GRE header. The GRE header specifies the
type of the encapsulated datagram and thus allows for tunneling other protocols than IP. GRE mode is also the default tunnel mode on Cisco
routers. gre also supports Cisco WCCP protocol, both version 1 and version 2.
The gre interfaces support a number of additional parameters to the ifconfig(8):
grekey Set the GRE key used for outgoing packets. A value of 0 disables the key option.
enable_csum Enables checksum calculation for outgoing packets.
enable_seq Enables use of sequence number field in the GRE header for outgoing packets.
EXAMPLES
192.168.1.* --- Router A -------tunnel-------- Router B --- 192.168.2.*
/
/
+------ the Internet ------+
Assuming router A has the (external) IP address A and the internal address 192.168.1.1, while router B has external address B and internal
address 192.168.2.1, the following commands will configure the tunnel:
On router A:
ifconfig greN create
ifconfig greN inet 192.168.1.1 192.168.2.1
ifconfig greN inet tunnel A B
route add -net 192.168.2 -netmask 255.255.255.0 192.168.2.1
On router B:
ifconfig greN create
ifconfig greN inet 192.168.2.1 192.168.1.1
ifconfig greN inet tunnel B A
route add -net 192.168.1 -netmask 255.255.255.0 192.168.1.1
NOTES
The MTU of gre interfaces is set to 1476 by default, to match the value used by Cisco routers. This may not be an optimal value, depending
on the link between the two tunnel endpoints. It can be adjusted via ifconfig(8).
For correct operation, the gre device needs a route to the decapsulating host that does not run over the tunnel, as this would be a loop.
The kernel must be set to forward datagrams by setting the net.inet.ip.forwarding sysctl(8) variable to non-zero.
SEE ALSO
gif(4), inet(4), ip(4), me(4), netintro(4), protocols(5), ifconfig(8), sysctl(8)
A description of GRE encapsulation can be found in RFC 2784 and RFC 2890.
AUTHORS
Andrey V. Elsukov <ae@FreeBSD.org>
Heiko W.Rupp <hwr@pilhuhn.de>
BUGS
The current implementation uses the key only for outgoing packets. Incoming packets with a different key or without a key will be treated as
if they would belong to this interface.
The sequence number field also used only for outgoing packets.
BSD
November 7, 2014 BSD