|
|
Sponsored Content
Operating Systems
Solaris
Error After Installing Tape Drive
Post 85773 by rajendra.rait on Friday 7th of October 2005 03:03:43 AM
10-07-2005
The server is working 
, the problem was with the path_to_inst file. I booted the machine in single user mode using the solaris cd 1 of 2.
ok boot cdrom -s
Later the machine booted in single user mode.
# mount /tmp/devices/pci@1f,0/pci@1/scsi@8/sd@0,0:a /tmp/a
# cp /tmp/a/etc/path_to_inst.old /tmp/a/etc/path_to_inst
# reboot
Yeppy, that's it done.
Later after the machine booted, i commented the lines started with "forceload" pertaining to my scenario in the /etc/system file.
Rebooted it again.
Thank you for time and help.
Regards,
Rajendra Rait.
, the problem was with the path_to_inst file. I booted the machine in single user mode using the solaris cd 1 of 2.ok boot cdrom -s
Later the machine booted in single user mode.
# mount /tmp/devices/pci@1f,0/pci@1/scsi@8/sd@0,0:a /tmp/a
# cp /tmp/a/etc/path_to_inst.old /tmp/a/etc/path_to_inst
# reboot
Yeppy, that's it done.
Later after the machine booted, i commented the lines started with "forceload" pertaining to my scenario in the /etc/system file.
Rebooted it again.
Thank you for time and help.
Regards,
Rajendra Rait.
|
|
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
hello,
I don't know what exactly the cause and the solution!!
suddenly I receive this error message when I want to use the 8mm tape drive
"I/O write error"
I disconnect the tape drive and I hook it in another WS and I receive this error :- ... (5 Replies)
Discussion started by: geoquest
5 Replies
2. Filesystems, Disks and Memory
Hi all, please help I am stuck.
I have installed a external unipack scsi tape drive. The tape drive is Exabyte Eliant 820. All I did was connected scsi cable and power it on. When issued "probe-scsi-all" command, the tape is correctly identified. However, when issued "dmesg | more" command, the... (4 Replies)
Discussion started by: dennis
4 Replies
3. UNIX for Advanced & Expert Users
I have a hp d 350 running on 10.2,im having a problem with the dds2 tape drive whenever i tried backing up larger files...i have remove the tape driver and add it using sam again but still the tape drive is not working .....is there a solution to this problem?
# tar cvf /dev/rmt/0m priso.ds
a... (3 Replies)
Discussion started by: giriplug
3 Replies
4. Linux
Hello. I have Redhat 8.0 on a laptop. Working good.
I wanted to install the tape drive that is physically attached to it. The tape drive worked fine under Windows98SE. It's one of those parallel QIC-80 drives and I confirmed that it is supported by FTape. It appears that FTape might already... (0 Replies)
Discussion started by: RuralTurtle
0 Replies
5. SCO
i have an ibm machine with dds4 drive running sco. i bought new hp dds4 tape for my back-up. the new tapes are not being read by the system, it says tape error, no such device. i've already clean the drive several times but still the same error occur. i've tried to use the same tape on our windows... (3 Replies)
Discussion started by: yackim
3 Replies
6. AIX
Brothers, I have a question on compatible issues.
I have a p570 server running on AIX5.3.0.0 TL04.
Recently I have received a 3590 tape drive with library and I am wonder whether I can make use of this tape drive for my normal daily backup of AIX 5.3.0.0 in p570 server.
Any driver or adapter... (1 Reply)
Discussion started by: kwliew999
1 Replies
7. SCO
Hello,
I'm having some issues with installing SCSI tape drive on SCO 5.0.6
hardware config shows the following adapters
%adapter 0xE800-0xE8FF 10 - type=alad ha=0 bus=0 id=7 fts=sto
%adapter 0x0170-0x0177 15 - type=IDE ctlr=secondary dvr=wd
%adapter - 3 - ... (3 Replies)
Discussion started by: ananth_ak
3 Replies
8. Solaris
Well I have just added new tape drive to my server (lto)
However I am getting few errors in using it. I have checked status with
#iostat -En : giving me few hard errors, few soft errors and execution error.
Also tape status is not visible as "no sense" its coming as "no additional sense".
I... (5 Replies)
Discussion started by: saurabh84g
5 Replies
9. AIX
Hi All
I am trying to copy files present in a partition (server 2) which is mounted to a different server (server 1) as tape drive is connected to it. I ran the below command to copy files within a partition:
svr01:root:/sunfileserver> tar -cvf *
a <foldername>/<filename>/<filename>
a... (4 Replies)
Discussion started by: vathsan
4 Replies
10. UNIX for Dummies Questions & Answers
Hi,
i installed a unix tape drive on my alphaserver. when i use a mt command it tells me there is no tape or device.
I have used the hardware manager and it shows the tape is present.
Can anyone help me understand why it cannot pick up the tape as a default? (1 Reply)
Discussion started by: ryks
1 Replies
LEARN ABOUT HPUX
install-solaris
install-solaris(1M) install-solaris(1M) NAME
install-solaris - install the Solaris operating system SYNOPSIS
install-solaris install-solaris invokes the Solaris Install program. Depending on graphical capability and available memory at the time of invocation, install-solaris invokes either a text-based installer or a graphical installer. The following minimum requirements for physical memory dictate which features are available during installation: For SPARC machines: 128 MB Minimum physical memory for all installation types 128 MB Minimum physical memory required for windowing system 384 MB Minimum physical memory required for graphical-based installation For x86 machines: 256 MB Minimum physical memory for all installation types 256 MB Minimum physical memory required for windowing system 512 MB Minimum physical memory required for graphical-based installation In some cases, even if the minimum physical memory is present, available virtual memory after system startup can limit the number of fea- tures available. install-solaris exists only on the Solaris installation media (CD or DVD) and should be invoked only from there. Refer to the for more details. install-solaris allows installation of the operating system onto any standalone system. install-solaris loads the software available on the installation media. Refer to the for disk space requirements. Refer to the for more information on the various menus and selections. See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWcdrom (Solaris instal- | | |lation media) | +-----------------------------+-----------------------------+ |Interface Stability |Evolving | +-----------------------------+-----------------------------+ pkginfo(1), install(1M), pkgadd(1M), attributes(5) It is advisable to exit install-solaris by means of the exit options in the install-solaris menus. 23 Sep 2005 install-solaris(1M)