Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Problem with N/W card in solaris
Top Forums UNIX for Dummies Questions & Answers Problem with N/W card in solaris Post 8326 by edwin_francis on Wednesday 10th of October 2001 03:32:55 AM
Old 10-10-2001
Java Problem with N/W card in solaris
hi all

We went to analyze a intel based server installed with Solaris 8 .previuosly on that machine Rhat 7.1 was loaded and working fine in the N/W. After we loaded Solaris 8 it got automatically rebooted when it comes to the Gui mode.The same happened thirce and we opted out to load without network support then the process went down smoothly .Then we configured the machine once again in the N/W but the same thing is still continuing i.e restarting everytime if a telnet session is opened or automatically after sometime.We came to know that it has taken the N/W card driver as Intel pro 100/B but the N/W card in our machine is Pro 100+ . we tried for the drivers on both intel and sun site.Can anybody help us in this problem ??we want to confirm is it the problem due to the Driver only ??

Thanks for help
Francis
Last edited by edwin_francis; 10-10-2001 at 05:07 AM..
 

10 More Discussions You Might Find Interesting

1. Filesystems, Disks and Memory

ethernet card for Solaris

Hi, How can i check the speed of the Ethernet card that my Sun server has and also how can i change it to full Duplex if it is set to half duplex? What is the file that takes care of this? (3 Replies)
Discussion started by: i2admin
3 Replies

2. IP Networking

Solaris 9 Ethernet Card Problems

I keeping plumbing my ethernet card and assigning it an IP address and netmask, but after I reboot it keeps losing this information. Can anyone help me solve this problem? I am using the command: ifconfig hme0 plumb <IP Address> netmask <Subnet Mask> broadcast + up I am running Solaris 9 OS. (2 Replies)
Discussion started by: saucierm
2 Replies

3. UNIX for Advanced & Expert Users

SCSI Card in Solaris 8

HI, I am trying to install Symbios SCSI PCI adapter in Ultra10 but unable to configure it. Getting following errors genunix: NOTICE: glm0: fault detected in device; service still unavailable genunix: NOTICE: glm0: Symbios PCI device (1000,3) not supported. Anyone has an idea, how to resolve... (1 Reply)
Discussion started by: s_aamir
1 Replies

4. SCO

LAN card problem

Dear all Im facing one problem in SCO 5.0.5 , its that in the server there are three LAN cards INTEL PRO 100 series but when we configure all the three cards then LAN stops working . self ping is possible but no one can ping the server. If we remove driver of any one card LAN starts working. Is... (1 Reply)
Discussion started by: ccvyas
1 Replies

5. Solaris

emulex card on solaris 9

Hello, I am new on solaris. We will connect our sun solaris system to the SAN and add 2 Emulex card on the system (solaris 9). Who have already done this and can give me the procedure to follow ? driver to install multipath etc... Thanks in advance Emmanuel (1 Reply)
Discussion started by: emma32
1 Replies

6. Solaris

Network card drivers for solaris?

Hi all, i have configured my solaris 5 .10 for internet connection by editing the files /etc/hosts/,/etc/resolve.config,/etc/defalutrouter and nsswitchconfig . during installation i was not requested for ip adddress even i plugged network cable. am i need to install any network card... (2 Replies)
Discussion started by: srikanthg
2 Replies

7. Solaris

Solaris 10 SCSI card question

I have 2 solaris boxes and trying to connect to D1000 to do clustering. I put the U cable to see the disks from both side, but I can't see any of the disks when I use format command. How can I verify that differential card is installed and configured correctly? Thanks in advance. (12 Replies)
Discussion started by: mokkan
12 Replies

8. Solaris

Old RSC card problem

All, I have a unique situation concerning RSC cards and would like to see if anyone has a solution. Here is the situation: We are migrating older versions of Solaris using ufsdump images to like older hardware. We basically installed a temporary Solaris O/S then copied the dumps over and... (5 Replies)
Discussion started by: sljack
5 Replies

9. Solaris

Problem with my Ethernet Card

Hi Gurus of Solaris. I have a problem yesterday when I was installing solaris in a x86 equipement I attached some log that I capture when I try to resolve the problem Any guru that can help please. Any command or procedure that I can run, please advice me Regards Andres (10 Replies)
Discussion started by: andresguillen
10 Replies

10. Solaris

Very new to Solaris and Sun, need help please (video card)

Hello all, I am trying to learn about Solaris and Sun systems so I purchased a SunFire 280r running Solaris 9 with a disk array from eBay. The system had no video card so I purchased a PGX32 card for the PCI slot and installed it. The problem is I have no video what so ever. I am familiar... (3 Replies)
Discussion started by: FTBTX
3 Replies

LEARN ABOUT NETBSD

xi

XI(4)							   BSD Kernel Interfaces Manual 						     XI(4)

NAME

     xi -- Xircom CreditCard Ethernet device driver

SYNOPSIS

     xi* at xirc?

     Configuration of PHYs may also be necessary.  See mii(4).

DESCRIPTION

     The xi driver provides support for the Xircom CreditCard family of PCMCIA Ethernet adapters.  Supported cards include:

	   Xircom CreditCard Ethernet II
	   Xircom CreditCard 10/100 Ethernet
	   Xircom RealPort 10/100 Ethernet + Modem (Ethernet function only)
	   Intel EtherExpress Pro/100
	   Compaq Netelligent 10/100

     Cards which should work, but have not been confirmed include:

	   Xircom RealPort Ethernet
	   Xircom RealPort 10/100 Ethernet

     Some Xircom Ethernet products are supported by the tlp(4) driver.

MEDIA SELECTION

     Media selection is done using ifconfig(8) using the standard ifmedia(4) mechanism.  Refer to those manual pages for more information.

SEE ALSO

     ifmedia(4), mii(4), netintro(4), pcmcia(4), tlp(4), xirc(4), ifconfig(8)

HISTORY

     The xi device driver appeared in NetBSD 1.5.

BUGS

     The driver suffers from poor performance.	Even with the 10/100 cards, do not expect more than ~450KB/s.  Some 10/100 cards may not autonego-
     tiate reliably and require manual media selection.

     The Xircom multifunction cards which contain both Ethernet and modem interfaces are known to have problems.  This is due to the card not
     reporting itself correctly as a multifunction card.

BSD
								   June 1, 2007 							       BSD
All times are GMT -4. The time now is 08:47 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy