How to List all Network cards Post: 76248

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

SCO Unix and Two Network Cards

Our shops server runs SCO Openserver 5 release 5. It has two network cards in it (one on 10.0.0.6 and one on 90.0.0.99). When I run scoadmin and look at the network settings it show both my 3com network cards and a loop back driver http://theentertainer.com/james/untitled.jpg Can anyone tell...

2. Solaris

Disable Network cards under boot Prom

Hi, I'm looking for a command to be able to disable a network card under the boot PROM. I need it to force my Jumpstart to use the Ethernet card of my server (V880) instead of my fiber card (gem0). Thanks, Fabien

3. AIX

Load balancing across network cards

The title speaks for itself. I have never attempted this but understand there is a way to use two network cards (en0 and en1) with the same IP address so as to load balance the traffic flow through both cards. Anyone know the answer?

4. Solaris

How to find network cards available ...

Hi all, I have a server running with Solaris and I have 2 Pci cards installed on this server (since a while), 1 with 4 coppers connections output and one with a Fiber network connection output. Today, this server is using the on board network connection (Ce0). How can I find the other...

5. Solaris

qfe errors and network cards

Hi All, Hope you are all doing good. In MY unix box i have 2 network cards. I want to know what if one network card fails. Does the second one will automatically take all the traffic or how it is supposed to work. Also in my logs i am seeing below errors . Can you throw some light of this qfe...

6. Solaris

Network cards - Routing

Hi all I hate networking, I hate everything to do with it. Its something I do in anger in one contract, then forget. This is more of a question / than a problem. So, on a solaris 10 server, using older qfe cards, Ive got a sun truck with 4 nics (qfe0,3,4,7), and a ipmp pair (hemo0,qfe1)....

7. Programming

retrieving network interface list

Hello I have a problem with retreiving network interface list using IOCTLs. I have 4 interfaces: $ ip addr 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue state UNKNOWN link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope...

8. Hardware

Slackware 13.1 can't configure two network cards

Hello everybody, I'm having troubles with Slackware 13.1 and network cards. I have one on-board Ethernet card (which is recognized and works okay) and a PCI Ethernet card (which is also recognized, but doesn't appear in 'ifconfig -a'). If i run a 'lspci', i can see the kernel recognized the...

9. UNIX for Dummies Questions & Answers

1 Server with 2 ethernet cards IP on seperate network. Possible?

Hi All, I have just setup a webserver running on a linux box. This server has 2 ethernet cards and only 1 is in used now. eg. 192.168.10.1 is my server IP. All users from 192.168.10.X can access my webserver. However, users from another LAN 10.10.10.X are not able to access my webserver. They...

10. Solaris

Get list of running network processes

Hello All I am trying to get a list of process or applications runninging on the network only. I should emphasize that im not interested in the application or process if its not using the network. I tried the good old netstat comand, but im not able to figure out how to list the running...

LEARN ABOUT NETBSD

ray

RAY(4)							   BSD Kernel Interfaces Manual 						    RAY(4)

NAME

     ray -- Raytheon Raylink / WebGear Aviator IEEE 802.11 2Mbps Wireless

SYNOPSIS

     ray* at pcmcia? function ?
     options RAY_PID_COUNTRY_CODE_DEFAULT=RAY_PID_COUNTRY_CODE_USA

DESCRIPTION

     The ray device driver supports the Raytheon Raylink and Aviator 2.4/PRO 802.11 FH 2Mbps wireless PCMCIA cards.  The cards can be operated in
     either ad-hoc or infrastructure modes. The operating mode is selectable with ifconfig(8) through a media option.

     To communicate with other 802.11 cards a common network id or NWID must be specified on each station that wishes to participate in the shared
     wireless network.	The NWID can be set with ifconfig(8).

     The device uses IEEE 802.11 standard Frequency Hopping Spread Spectrum signaling and operates in the ranges of 2.400 to 2.4835 Gigahertz.
     This frequency range is further restricted by country according to that country's regulations.  Currently the ray driver defaults to using
     the ranges appropriate for the USA.  To change this setting you must define the kernel option RAY_PID_COUNTRY_CODE_DEFAULT to one of the fol-
     lowing values:

     RAY_PID_COUNTRY_CODE_USA
     RAY_PID_COUNTRY_CODE_EUROPE
     RAY_PID_COUNTRY_CODE_JAPAN
     RAY_PID_COUNTRY_CODE_KOREA
     RAY_PID_COUNTRY_CODE_SPAIN
     RAY_PID_COUNTRY_CODE_FRANCE
     RAY_PID_COUNTRY_CODE_ISRAEL
     RAY_PID_COUNTRY_CODE_AUSTRALIA

     The output power of the transceiver is 100mW and the card's power consumption is 365 mA @ 5 volts.  The transmission range in open air (line
     of sight) is a maximum of 1000 feet (or ~304 meters), and indoors (i.e., with obstructions) it is a maximum of 500 feet (152 meters).

HARDWARE

     Cards supported by the ray driver include:

     WebGear Aviator 2.4
     WebGear Aviator PRO
     Raytheon Raylink WLAN

DIAGNOSTICS

     ray0: card failed self test: status x  Indicates the card has failed its initial startup tests.

SEE ALSO

     ifmedia(4), intro(4), pcmcia(4), ifconfig(8)

HISTORY

     The ray driver first appeared in NetBSD 1.5.

AUTHORS

     The ray driver was written by Christian E. Hopps <chopps@NetBSD.org>.

BUGS

     Currently the infrastructure mode is untested, and authentication using WEP is unimplemented.

BSD
								 January 24, 2000							       BSD