09-25-2001
One logical next troubleshooting step is to check with the OS vendor to see if their kernel support the SCSI host adapter you are trying to use & support the tape drive.
Let us know if you find a good link to this H/W documentation.
10 More Discussions You Might Find Interesting
1. Filesystems, Disks and Memory
I was using an external SCSI disk on a Sun Ultra60 (Solaris 7) as the boot device. It was labelled c1t0d0. I then moved it into the internal removable mounts and it should become c0t0d0, but it apparently didn't change properly. When the machine boots, it gets host information from the disk... (2 Replies)
Discussion started by: Solaris
2 Replies
2. Solaris
Hi. I need to find a simple SCSI adapter card for a Sun Ultra 5 workstation. I don't need the type w/ ethernet attached (e.g. X1032) as I already have ethernet onboard & they are more spendy.
I know Adaptec is out, but what unit would work? I am attaching an external SCSI tape unit to this... (4 Replies)
Discussion started by: Plain Person
4 Replies
3. Solaris
Okay. I admit I'm sort of a newbie in this regard.
I installed a SCSI adapter on a Sun Ultra 5 workstation. I did the standard STOP-A on the startup and got the OK prompt. I then tried probe-scsi-all. It dumps me back @ the OK prompt w/ no message whatsoever. I tried probe-scsi, nothing.
... (3 Replies)
Discussion started by: Plain Person
3 Replies
4. AIX
I have 1 PCI-X Dual Channel Ultra320 SCSI Adapter card for my p570 server. I would like to split the 2 channels for the usage of 2 tape drives in different LPARs. Is that possible?
For example, I have 2 LPARs running in p570 server, LPAR-A configured the Ultra320 card as pci7 in slot... (11 Replies)
Discussion started by: kwliew999
11 Replies
5. SCO
I am installing SCO UNIX 5.0.6 in X3400, every thing are install except Adaptec 29320ALP Card (Attached DAT Drive) because their driver are available in btld formate Fllopy DISk and SCO Unix 5.0.6 not support USB Floppy, Can anybody inform us any other method to installed the Adaptec Ultra 120... (3 Replies)
Discussion started by: hafizurr
3 Replies
6. UNIX and Linux Applications
Hey everyone.
I am trying to set up four sun servers. They all came with an adaptec storagetek raid liveCD. On the liveCD there is a utility called "Arcconf" which is supposed to be used to configure the storage arrays. The example given in their documentation uses this as an example:
ARCCONF... (2 Replies)
Discussion started by: msarro
2 Replies
7. Hardware
I need to connect 80pin SCA Ultra320 SCSI hdd to 68pin.
There are rumors that some bad "passive" adapters with problematic termination can fry the HDD. The adapter we got is Assmann ABSCA-2. Hard drive is 'Fujitsu MAW3073NC'
Do we need to set any jumpers before turning it on?
We already had... (0 Replies)
Discussion started by: orange47
0 Replies
8. SCO
OK group, it's been 12 years since I worked with SCO. I need some direction here:
SCO Openserver 5.07
I have a server with a bad motherboard. I have moved the SCSI adapter and hard drive to another computer. This new server has different hardware so I must install the chipset drivers for... (1 Reply)
Discussion started by: jscholz
1 Replies
9. HP-UX
I am trying to reload a RP4440 with 2x300gb disks and dual Port Network card, with HPUX 11.11 Sept 2003. When the os boots and and gets to the main menu to install HPUX or run recovery, it cannot find the disks or NIC.
At the OS prompt (after loading files), ioscan shows the Class ba, and shows... (0 Replies)
Discussion started by: mrmurdock
0 Replies
10. AIX
Hi,
We had a hardware problem with an IBM System p5 server, with AIX 5.2
We restore from a tape the last backup we had, but the server does not boot up as expected.
The server try to mount some directories from a storage, but could not comunicate with them, we check the FC and everything is... (12 Replies)
Discussion started by: trevian3969
12 Replies
HT(4) Kernel Interfaces Manual HT(4)
NAME
ht - TM-03/TE-16,TU-45,TU-77 MASSBUS magtape interface
SYNOPSIS
/sys/conf/SYSTEM:
NHT ht_drives # TE16, TU45, TU77
/etc/dtab:
#Name Unit# Addr Vector Br Handler(s) # Comments
ht ? 172440 224 5 htintr # tu 16 massbus tape
major device number(s):
raw: 6
block: 0
minor device encoding:
bits 0003 specify HT drive
bit 0004 specifies no-rewind operation
bit 0010 specifies 1600BPI recording density instead of 800BPI
DESCRIPTION
The tm-03/transport combination provides a standard tape drive interface as described in mtio(4). All drives provide both 800 and 1600
bpi; the TE-16 runs at 45 ips, the TU-45 at 75 ips, while the TU-77 runs at 125 ips and autoloads tapes.
FILES
/dev/MAKEDEV script to create special files
/dev/MAKEDEV.local script to localize special files
SEE ALSO
mt(1), tar(1), tp(1), mtio(4), tm(4), ts(4), dtab(5), autoconfig(8)
DIAGNOSTICS
tu%d: no write ring. An attempt was made to write on the tape drive when no write ring was present; this message is written on the termi-
nal of the user who tried to access the tape.
tu%d: not online. An attempt was made to access the tape while it was offline; this message is written on the terminal of the user who
tried to access the tape.
tu%d: can't change density in mid-tape. An attempt was made to write on a tape at a different density than is already recorded on the
tape. This message is written on the terminal of the user who tried to switch the density.
tu%d: hard error bn%d er=%b ds=%b. A tape error occurred at block bn; the ht error register and drive status register are printed in
octal with the bits symbolically decoded. Any error is fatal on non-raw tape; when possible the driver will have retried the operation
which failed several times before reporting the error.
BUGS
If any non-data error is encountered on non-raw tape, it refuses to do anything more until closed.
The system should remember which controlling terminal has the tape drive open and write error messages to that terminal rather than on the
console.
3rd Berkeley Distribution January 28, 1988 HT(4)