Sponsored Content
Full Discussion: xdmcp on HP-UX
Operating Systems HP-UX xdmcp on HP-UX Post 64075 by dburton30 on Saturday 26th of February 2005 04:23:53 PM
Old 02-26-2005
Unless things have change recently Xdmcp is normally set on a standard HP-UX install. It may have been turned off. Look here - /usr/dt/config/Xaccess

The lines should look like this (uncommented):

* # grant service to all remote displays
* CHOOSER BROADCAST #any indirect host can get a chooser

If commented out then it won't work. Also, I assume your trying to use ReflectionX or Exceed to connect. I gather the settings for these should be:

http://home.tampabay.rr.com/batcave/...tes.htm#Exceed

or

http://home.tampabay.rr.com/batcave/unixnotes.htm#List

Hope this helps.
 

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

XDMCP setup

How do you verify your XDMCP setup on Sun Solaris? I am trying to establish a connection, but no XDMCP servers were found. (1 Reply)
Discussion started by: heinb
1 Replies

2. IP Networking

xdmcp and netstat

On my linux box, i run netstat -l and i see xdmcp in the list but it doesn't have LISTEN as its state, see what it shows below, I'm wondering if this might explain why i can't see it in my exceed broadcast listing of servers broadcasting on our net? My unix boxes don't show this at all. Proto ... (1 Reply)
Discussion started by: kymberm
1 Replies

3. Solaris

xdmcp on Solaris 10 x86

I recently downloaded and installed Solaris 10 on an Intel PC. I want to connect to it via XDMCP from another client. I found you can enable xdmcp as follows: Launch -> Applications -> Utilities -> Administration -> Login Screen Setup Then selected the XDMCP tab and click the box that... (1 Reply)
Discussion started by: lyonsd
1 Replies

4. HP-UX

xdmcp config

hi everybody, can anyone please tell me what are things for verify to have an xdmcp connexion ton HPUX 10.20 host best regards (0 Replies)
Discussion started by: hmaiida
0 Replies

5. UNIX for Dummies Questions & Answers

XDMCP no password

Hello all, Does anyone know or have configure their system to allow no password during an XDMCP session. I' m running Redhat whit gdm manager. Thanks! (0 Replies)
Discussion started by: larryase
0 Replies

6. SCO

xdmcp dies in sco600

We have just installed a sco 600 server. Xdmcp comes up in the chooser but if you don't log in within a few minutes it disappears and you have to log in and then out on the console before you can see it in the chooser. Xdmcp is suppossed to be setup for continuous logins automatically. We... (0 Replies)
Discussion started by: khafner
0 Replies

7. Solaris

Help: for XDMCP

Hi, Boss i have a problem about open the Graphic remote. when i used the Xmanager2.0 connect to the Sun Fire880 with Sun solaris 2.8 software. prompt to following information: XDMCP connection failed: retry? so can some body told me how the check the XDMCP protocol was enable...and the port 177... (9 Replies)
Discussion started by: surainbow
9 Replies

8. AIX

How to enable XDMCP?

Hello everyone, I installed AIX the other day (several times!) but I can't get XDMCP to work. I remember from when I installed it the last time it worked out of the box. So why doesn't it work now? This is the error message I get: XDMCP fatal error: Session failed Session 2 failed for... (3 Replies)
Discussion started by: Kotzkroete
3 Replies

9. Solaris

XDMCP Error

Hi Friends, I am not able to login through X browser from Windows Machine to Sun Fire V890 server. Solaris 10 is installed on this machine. Please suggest me what changes need to be done in Solaris Server. Thanks in Advance (2 Replies)
Discussion started by: durgaprasadr13
2 Replies
URL(4)							   BSD Kernel Interfaces Manual 						    URL(4)

NAME
url -- Realtek RTL8150L USB Ethernet driver SYNOPSIS
url* at uhub? urlphy* at mii? DESCRIPTION
The url driver provides support for USB Ethernet adapters based on the Realtek RTL8150L USB-ether bridge chip. The url driver supports the following adapters: CompUSA USBKR100 GreenHouse GH-USB100B Melco Inc. LUA-KTX Sitecom LN013 For more information on configuring this device, see ifconfig(8). DIAGNOSTICS
url%d: watchdog timeout A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the transmission before a timeout expired. url%d: no memory for rx list The driver failed to allocate an mbuf for the receiver ring. SEE ALSO
arp(4), mii(4), netintro(4), usb(4), ifconfig(8) HISTORY
The url device driver first appeared in NetBSD 1.6. AUTHORS
The url driver was written by Shingo WATANABE <nabe@nabechan.org>. BSD
September 18, 2006 BSD
All times are GMT -4. The time now is 10:02 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy