08-24-2001
9 More Discussions You Might Find Interesting
1. Solaris
Hi , I came across a SUN server whereby it was installed with additional ethernet card. By right in any configuration, you would probably see the onboard ports Net0,Net1 and so on should correspond to e1000g0,e1000g1...
But instead the ext PCI takes precedence in the order and the Net0 becomes... (3 Replies)
Discussion started by: incredible
3 Replies
2. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
3. Solaris
can anyone help me fix this? what command should I use to bring them back to "TRUE"?
Interface Speed Duplex Autoneg
--------- ----- ------ -------
ce0 100 Mbit/s FULL FALSE
ce5 100 Mbit/s FULL ... (3 Replies)
Discussion started by: uuontario
3 Replies
4. AIX
Hi admins
i want to assign new ip adress to my aix 5.3 machine which is in LPAR
ent3 Available Virtual I/O Ethernet Adapter (l-lan)
ent0 Available 05-08 2-Port 10/100/1000 Base-TX PCI-X Adapter (14108902)
ent1 Available 05-09 2-Port 10/100/1000 Base-TX PCI-X Adapter (14108902)
ent2... (0 Replies)
Discussion started by: newaix
0 Replies
5. Solaris
Hi folk,
I have this hardware faunty message, but dont know which hardware is this ? can you guide me ?
--------------- ------------------------------------ -------------- ---------
TIME EVENT-ID MSG-ID SEVERITY
---------------... (9 Replies)
Discussion started by: dehetoxic
9 Replies
6. Solaris
I couldn't install my nic in solaris 10. I compiled and added
the driver but failed to attach the driver and ifconfig output
shows only loopback dev. Please see the following output and tell
me whether my nic has been detected and why the driver failed to
attach?
My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies
7. IP Networking
I am new in squid proxy.
My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)?
Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies
8. Red Hat
Dear All
I want tune my NIC's rps, rfs and xps value.
In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1).
Here is the question? Which device should I modify ?
eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0)
Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies
9. Linux
Hello Admins,
My ask is how can I add two different subnet IPs to same box with two different gateways?
The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware.
How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies
URL(4) BSD Kernel Interfaces Manual URL(4)
NAME
url -- Realtek RTL8150L USB Ethernet driver
SYNOPSIS
url* at uhub?
urlphy* at mii?
DESCRIPTION
The url driver provides support for USB Ethernet adapters based on the Realtek RTL8150L USB-ether bridge chip.
The url driver supports the following adapters:
CompUSA USBKR100
GreenHouse GH-USB100B
Melco Inc. LUA-KTX
Sitecom LN013
For more information on configuring this device, see ifconfig(8).
DIAGNOSTICS
url%d: watchdog timeout A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the
transmission before a timeout expired.
url%d: no memory for rx list The driver failed to allocate an mbuf for the receiver ring.
SEE ALSO
arp(4), mii(4), netintro(4), usb(4), ifconfig(8)
HISTORY
The url device driver first appeared in NetBSD 1.6.
AUTHORS
The url driver was written by Shingo WATANABE <nabe@nabechan.org>.
BSD
September 18, 2006 BSD