Thread Tools Search this Thread
Top Forums UNIX for Dummies Questions & Answers Hardware/NIC
# 1  
Old 08-24-2001


I'm going to install Redhat 7.1 om my Compaq presario 1200 (laptop) and dual boot with Win2K. Now i have learned that my 3com fem556b-global pc-card not is supported (read on 3com's site).

My question is now can i get my card to work under Linux or even better is there a pc-card that is supported both by Linux and Win2K? And not to expencive. Is there any HCL for Linux/UNIX?

Thank for any help.

//Andreas Rönnelin
# 2  
Old 08-24-2001
there is a hcl for linux. it should be in the book.

i know linksys and netgear and some 3com cards are all supported in both.
# 3  
Old 08-24-2001

Witch book?
Where can i find it? Any one that can check the card for me?

//Andreas Rönnelin
# 4  
Old 08-24-2001
have you checked the red hat site? it has the hcl right there. Very easy to find.

Login or Register to Ask a Question

Previous Thread | Next Thread

9 More Discussions You Might Find Interesting

1. Linux

Add two different subnet public IPs to single NIC or two different NIC on same box

Hello Admins, My ask is how can I add two different subnet IPs to same box with two different gateways? The issue is I can connect to the box when I am on ethernet LAN, but I am not able to connect to the same IP when I am on wifi. The server is RHEL 7 VM on vmware. How can I get connected... (4 Replies)
Discussion started by: snchaudhari2
4 Replies

2. Red Hat

I want to tune NIC's rps, rfs and xps value. which NIC device should I modify.

Dear All I want tune my NIC's rps, rfs and xps value. In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1). Here is the question? Which device should I modify ? eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0) Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies

3. IP Networking

squid proxy: one NIC for inbound & one NIC for outbound?

I am new in squid proxy. My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)? Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies

4. Solaris

x86 Solaris 10 nic driver added but not attached. NIC is not detected.

I couldn't install my nic in solaris 10. I compiled and added the driver but failed to attach the driver and ifconfig output shows only loopback dev. Please see the following output and tell me whether my nic has been detected and why the driver failed to attach? My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies

5. Solaris

Hardware faulty, but which hardware?

Hi folk, I have this hardware faunty message, but dont know which hardware is this ? can you guide me ? --------------- ------------------------------------ -------------- --------- TIME EVENT-ID MSG-ID SEVERITY ---------------... (9 Replies)
Discussion started by: dehetoxic
9 Replies

6. AIX

assigning ip to second nic

Hi admins i want to assign new ip adress to my aix 5.3 machine which is in LPAR ent3 Available Virtual I/O Ethernet Adapter (l-lan) ent0 Available 05-08 2-Port 10/100/1000 Base-TX PCI-X Adapter (14108902) ent1 Available 05-09 2-Port 10/100/1000 Base-TX PCI-X Adapter (14108902) ent2... (0 Replies)
Discussion started by: newaix
0 Replies

7. Solaris

NIC problem

can anyone help me fix this? what command should I use to bring them back to "TRUE"? Interface Speed Duplex Autoneg --------- ----- ------ ------- ce0 100 Mbit/s FULL FALSE ce5 100 Mbit/s FULL ... (3 Replies)
Discussion started by: uuontario
3 Replies

8. HP-UX

how can I determine which NIC card is virtual NIC Card

how can I determine which NIC card is virtual NIC Card which condition can make a decision Does HP UX have Virtual Network Adapter Concept if ,it has where I can Find if I Install Virutal Network Adapter or which command that i can get it or which software can generate thanks (2 Replies)
Discussion started by: alert0919
2 Replies

9. Solaris

Cause of NIC changes ...?

Hi , I came across a SUN server whereby it was installed with additional ethernet card. By right in any configuration, you would probably see the onboard ports Net0,Net1 and so on should correspond to e1000g0,e1000g1... But instead the ext PCI takes precedence in the order and the Net0 becomes... (3 Replies)
Discussion started by: incredible
3 Replies
Login or Register to Ask a Question