|
|
Sponsored Content
Special Forums
IP Networking
Binding Virtual IP address to NIC
Post 52304 by dkaplowitz on Tuesday 15th of June 2004 12:54:39 PM
06-15-2004
|
|
9 More Discussions You Might Find Interesting
1. IP Networking
I have a SCO OpenServer 5.0.5 and my cuestion is can i have 2 ip address in one nic?, how?.
Thanks. (1 Reply)
Discussion started by: dvl
1 Replies
2. Solaris
Hi,
We have a 4 port Sun gigaswift NIC card on our sun fire server.
If the card is a physical one I know how to check the settings/speed. But since this is a virtual card with 4 ports , I am not sure as how we can check the settings.
Details
-----------
root:/> ifconfig -a
lo0:... (3 Replies)
Discussion started by: pray44u
3 Replies
3. Shell Programming and Scripting
how can I know the Network Interface Card physical address? (4 Replies)
Discussion started by: nokia1100
4 Replies
4. HP-UX
how can I determine which NIC card is virtual NIC Card
which condition can make a decision
Does HP UX have Virtual Network Adapter Concept
if ,it has
where I can Find if I Install Virutal Network Adapter
or which command that i can get it
or which software can generate
thanks (2 Replies)
Discussion started by: alert0919
2 Replies
5. IP Networking
hi all,
i have an udp based application that doesn't bind to any particular address.
-->while sneding the packets, i have some doubts....
1) can the packet be transmitted with an source ip address as 0.0.0.0
2) if we select an interface based on destination ip address,... (0 Replies)
Discussion started by: vijaypdp2006
0 Replies
6. UNIX for Dummies Questions & Answers
Hi guys,
I got one problem which I definetily no idea.
What would the physical address be for virtual address?
1) 2ABC
2) 3F4B
Here is the page table:see attached
Thank you sos sososososso much!! (0 Replies)
Discussion started by: lemon_06
0 Replies
7. Solaris
Hi everybody!
I'm facing a problem and I doubt about the solution (I'm not very familiar with old *NIXs).
An external network supplier (let's call them "telco") just installed new communication components that filters MAC addresses.
I have a Solaris 5 server, with 1 NIC (hte0) which is... (6 Replies)
Discussion started by: Isharfoxat
6 Replies
8. Solaris
Hi All,
does any body know how to create Virtual NIC in Solaris 10
if any one have good article or reference
kindly provide me
i try to Google
but i didn't find good one (7 Replies)
Discussion started by: jamisux
7 Replies
9. Red Hat
am try to create another network card as virtual eth0:1
but when i restart the server it want be appear i have to create it again what is the solution for this . (6 Replies)
Discussion started by: leganti
6 Replies
LEARN ABOUT NETBSD
url
URL(4) BSD Kernel Interfaces Manual URL(4) NAME
url -- Realtek RTL8150L USB Ethernet driver SYNOPSIS
url* at uhub? urlphy* at mii? DESCRIPTION
The url driver provides support for USB Ethernet adapters based on the Realtek RTL8150L USB-ether bridge chip. The url driver supports the following adapters: CompUSA USBKR100 GreenHouse GH-USB100B Melco Inc. LUA-KTX Sitecom LN013 For more information on configuring this device, see ifconfig(8). DIAGNOSTICS
url%d: watchdog timeout A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the transmission before a timeout expired. url%d: no memory for rx list The driver failed to allocate an mbuf for the receiver ring. SEE ALSO
arp(4), mii(4), netintro(4), usb(4), ifconfig(8) HISTORY
The url device driver first appeared in NetBSD 1.6. AUTHORS
The url driver was written by Shingo WATANABE <nabe@nabechan.org>. BSD
September 18, 2006 BSD