10-20-2003
Problem with installing mandrake 7.2
I was trying to install mandrake 7.2 in my newly brought used intel pentium III processor with no operating system installed in it. In the boot sequence in the BIOS there is no "boot from the cdrom" option so I made a "boot disk" to boot from the floppy drive.
While booting from the floppy I got some thing like this
" What is the type of the cdrom you have?"
SCSI
other CDROM.
When I hit "other CDROM" option then I am getting many options but none are working on it.IT only says "cannot load the module".
I am getting this message even before i enter the cd in to the drive.
Can some body here can solve this mystery...?
Any help is highly appreciated.
Thanks
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Sup
Ok, here is the problem.
I bought Linux Manrake v.8.1 Power Pack Edition
I booted it up, and got to the partitioning part of the installation. As Manrake users would know, there are several options that you can install with. There is Custom Patitioning, Format and load w/ Linux on it, add... (4 Replies)
Discussion started by: KyPeN
4 Replies
2. UNIX for Dummies Questions & Answers
Edit your /etc/modules.conf file to either remove or comment out the two lines :
alias sound-slot-0 snd-card-intel8x0
above snd-card-intel8x0 snd-pcm-oss
...and replace them with the following line:
alias sound i810_audio
....viola! After saving and rebooting, now I gots da sound!... (0 Replies)
Discussion started by: DownSouthMoe
0 Replies
3. SuSE
ihave mandrake 9.2 (will upgrade soon to 10) but anyways, i can't get the Hard drive or the CD-ROM or Floppy to show up on the desktop. can anyone help me out? (11 Replies)
Discussion started by: linux_newbe
11 Replies
4. Slackware
I am pretty new to Unix/linux and have been itching to use a linux os for a while. And after some research i found that Mandrake was the best for someone like me. I need to know what files i need to download to make a boot disc(s) to make my laptop run only linux. The laptop runs around 200-500mhz... (10 Replies)
Discussion started by: Infidel
10 Replies
5. Linux
Hey everyone,
I'm new to the forum.
I have a problem with Mandrake 8.00; i have installed it on my old PC with no problems (none mentioned) but on re-booting after the installation it just hangs after listing the devices: Hard Disk, CD-ROM & Floppy A.
I have installed it on Packard Bell with... (2 Replies)
Discussion started by: sybella1
2 Replies
6. Solaris
Hi all, i am new in solaris, i have a solris server Ultra 60, when i turn on the server show me the follow error:
Bad magic number in disk label
can`t open disk label package
Boot device: net File and args:
Timeouot waiting for ARP/RARP packet
Timeouot waiting for ARP/RARP packet
....
I... (3 Replies)
Discussion started by: elimunoz
3 Replies
7. UNIX for Dummies Questions & Answers
hi. I am newbie in Unix. I wanted to install Free BSD 5.2.1 to my computer which winXp was already installed. But i couldn't.
I chose Standard. Then it said you are going to use dos style fdisk partitioning. Then a window displayed begining like this.
WARNING: A geometry of 155127/16/63 for... (2 Replies)
Discussion started by: sualcavab
2 Replies
8. Solaris
when i try to build pine unix tells me it can't find make
# ./build xxx
make args are CC=cc soc
Including LDAP functionality
ln: cannot create c-client: File exists
ln: cannot create mtest: File exists
ln: cannot create mailutil: File exists
ln: cannot create imapd: File exists
ln:... (0 Replies)
Discussion started by: vutty81
0 Replies
9. Solaris
Hi all,
I tried to install Sun Solaris 10 on a X-86 based machine. I have dedicated entire diskspace to create auto partition. My hardware config is below:
Main Board : Asus
Processor : Intel 945 , 3 G/Hz
RAM : 1 Gigs
Diskspace : 80 Gigs
When I install, installation goes successful.... (1 Reply)
Discussion started by: naw_deepak
1 Replies
10. Red Hat
I have dexx xps 14.I was installing rhel6.But the installation hanged at following step
initializing hardware detection.................
installion didnt go further (2 Replies)
Discussion started by: shamapraveen
2 Replies
LEARN ABOUT DEBIAN
installgrub
installgrub(1M) installgrub(1M)
NAME
installgrub - install GRUB in a disk partition or a floppy
SYNOPSIS
/sbin/installgrub [-fm] stage1 stage2 raw-device
The installgrub command is an -only program. GRUB stands for GRand Unified Bootloader.
installgrub installs GRUB stage 1 and stage 2 files on the boot area of a disk partition. If you specify the -m option, installgrub
installs the stage 1 file on the master boot sector of the disk.
The installgrub command accepts the following options:
-f
Suppresses interaction when overwriting the master boot sector.
-m
Installs GRUB stage1 on the master boot sector interactively.
The installgrub command accepts the following operands:
stage1
The name of the GRUB stage 1 file.
stage2
The name of the GRUB stage 2 file.
raw-device
The name of the device onto which GRUB code is to be installed. It must be a character device that is readable and writable. For disk
devices, specify the slice where the GRUB menu file is located. (For Solaris it is the root slice.) For a floppy disk, it is
/dev/rdiskette.
Example 1: Installing GRUB on a Hard Disk Slice
The following command installs GRUB on a system where the root slice is c0d0s0:
example# /sbin/installgrub /boot/grub/stage1
/boot/grub/stage2 /dev/rdsk/c0d0s0
Example 2: Installing GRUB on a Floppy
The following command installs GRUB on a formatted floppy:
example# mount -F pcfs /dev/diskette /mnt
# mkdir -p /mnt/boot/grub
# cp /boot/grub/* /mnt/boot/grub
# umount /mnt
# cd /boot/grub
# /sbin/installgrub stage1 stage2 /dev/rdiskette
/boot/grub
Directory where GRUB files reside.
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
boot(1M), fdisk(1M), fmthard(1M), kernel(1M), attributes(5)
Installing GRUB on the master boot sector (-m option) overrides any boot manager currently installed on the machine. The system will always
boot the GRUB in the Solaris partition regardless of which fdisk partition is active.
24 May 2005 installgrub(1M)