05-15-2018
The original machine had an older version of the Activant software on it so I thought I would have to update the software to the same version that the new server is running in order to restore. The original machine is a Dual Pentium III with 2 GB ram with adaptec AIC 7899 SCSI controller
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I've just installed Unix SCO OpenServer System v in an Intel PC and Everithing ok, except just one thing, in the begining of the installation the wizard asked me about the mouse , i have a generic 3 buttons mouse and i took a logitech and did not work
i need to change the mouse configuration, ... (2 Replies)
Discussion started by: jimmyvaldes
2 Replies
2. UNIX for Dummies Questions & Answers
hello!
when i try to make my system dual boot with both win98 & sco open server 5.5 it doesn't work at all.neither win98 take start nor sco open server boots.what should i do ?
kindly help me
thanks (1 Reply)
Discussion started by: buntty
1 Replies
3. IP Networking
I have certain problems while Installing UNIX OPENSERVER.Could anyone solve that if I provide that problem. (3 Replies)
Discussion started by: Rajraius
3 Replies
4. SCO
Hi everyone,
We r installing sco openserver 5.07 on dell poweredge 2800 but we are facing problem when installing SCSI-raid drivers. Dell provide Perc4 raid card and we dont found raid drivers for this specific raid card. So we r stuck up on primary stage and we also dont know the... (2 Replies)
Discussion started by: mineshkoli
2 Replies
5. SCO
we are installing Openserver 5.0.7, system have SAS controller (Hard Disk Attached) as well as Adaptec ultra 320 controller (Tape Drive Attached).
At the time of installation we link both driver BTLD
Boot: Defbootstr link=accraid ad320
Aftes succesfully installation of accraid btld... (6 Replies)
Discussion started by: hafizurr
6 Replies
6. SCO
I'm trying to install openserver 6.0 on a locally assembled ACPI Multiprocessor PC with an intel core 2 dou e4400 @ 2 ghx and a WD8000JD SATA HD. Immediately after the startup screen I get "PANIC: kernel-mode address fault on kernel address 0xf000ff53". I get this message even if the drive is... (1 Reply)
Discussion started by: tvmccorm
1 Replies
7. SCO
can not for the life of me workout which BTLD to load allways shows no HDD available can any one give me a clue
tried
hpsas
aacraid
lsil
a160
a320
server is a ML310 G4 ?????:confused::confused: (7 Replies)
Discussion started by: wildginger
7 Replies
8. SCO
hello, i want to install release 5.0.5 on my notebook but the system hangs when extracing files from source media in fact after configuration all of setting please help me:confused: (1 Reply)
Discussion started by: hossein
1 Replies
9. UNIX for Advanced & Expert Users
Hi All ,
I wanted to install SCO Open server 5.0.7 on HP DC7600 Desktop Machine, is there any bootloader and which site i can find it to enable me install it because the system is not recognizing the Hard disk just like the ML G Series machine installations.
Please help if you have done this... (4 Replies)
Discussion started by: davosky
4 Replies
10. UNIX for Advanced & Expert Users
Hi:
I'm installing SCO Open Server 6.0v on VMWare ESXi,
The instalation procedure giving by UnXis is using OVF deploy template and
it create a primary partition of 10gb only.
Any one know, if the OVF template could be edited to create a larger partition??
Thanks (0 Replies)
Discussion started by: Ccarballo
0 Replies
SF(4) BSD Kernel Interfaces Manual SF(4)
NAME
sf -- Adaptec AIC-6915 10/100 Ethernet driver
SYNOPSIS
sf* at pci? dev ? function ?
Configuration of PHYs may also be necessary. See mii(4).
DESCRIPTION
The sf device driver supports the Adaptec AIC-6915 10/100 Ethernet chip. This chip is found on several Adaptec Ethernet boards:
o ANA-62011 Single port 10/100 64-bit
o ANA-62022 Dual port 10/100 64-bit
o ANA-62044 Quad port 10/100 64-bit
o ANA-62020 Single port 100BASE-FX 64-bit
o ANA-69011 Single port 10/100 32-bit
SEE ALSO
arp(4), ifmedia(4), mii(4), netintro(4), pci(4), ifconfig(8)
HISTORY
The sf driver first appeared in NetBSD 1.6.
AUTHORS
The sf driver was written by Jason R. Thorpe <thorpej@NetBSD.org>.
BUGS
The sf driver does not support the IPv4/TCP/UDP checksum function of the AIC-6915.
The sf driver does not support the VLAN function of the AIC-6915.
BSD
June 18, 2001 BSD