T4 replaced motherboard - recovering LDOM config? Post: 303000874

7 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Which motherboard???

Hello All I'm looking to buy a new motherboard because my current one (ABIT BE6-II v1.1) doesn't support the installation of Unix. I'd like to keep my CPU (Genuine Intel PIII 800 Mhz) and memory (512 Meg) to use on the new motherboard. My CPU is one of those cartridge types which is mounted...

2. Filesystems, Disks and Memory

Motherboard Compatibility

Hi there,, I URGENTLY need to know if the Gigabyte GA 8IDML Motherboard is compatible with the Unix BSD. We need to know if we should buy new boards before we can use the product. Thanking you Hannelie Bosch:confused: :confused:

3. UNIX for Dummies Questions & Answers

Replacing Motherboard

My UNIX (SCO) crashed. I replaced the MB and tried reconfiguring all the devices etc...the system detects the NIC ok, but the following are not working properly a) keyboard/credit card swipe which connects to PS/2 port not working b) unable to connect to another PC in the small network c)...

4. Solaris

corrupted motherboard

hi i have a sun server V890 and i added two cpu/memory modules to it but it caused the motherboard to become corrupted could you please help me find what causes this problem and how to avoid it because i changed the corrupted motherboard and i want to do the expansion and I'm scared that ...

5. Solaris

Change motherboard

Hello, I am fairly new to Solaris ... You can change the motherboard of a computer with solaris 10? Exist a tutorial for this or can you tell me how to do this? Thanks in advance

6. Solaris

Network Config on Zone in a Guest LDOM

Solaris for Sparc 11.1 with the latest patches. Created a Guest LDOM with two vnet's net0 and net1, installed a guest whole root, ip exclusive zone that I want to be able to utilize DHCP. I have been able to create the zone but unable to get it to boot because I am unable to assign an anet to it....

7. Solaris

T4-2 - Memory DIMM issue - ldom config resets to factory-default

Which basically means the ldoms that were on there are not starting (not even showing). If I do ldm list-config it shows live config as next reboot. But, of course, next reboot it reverts back to factory default again. I must admit I'm wondering if its doing this becasue (with the...

LEARN ABOUT NETBSD

stge

STGE(4) 						   BSD Kernel Interfaces Manual 						   STGE(4)

NAME

     stge -- Sundance/Tamarack TC9021 Gigabit Ethernet driver

SYNOPSIS

     stge* at pci? dev ? function ?

     Configuration of PHYs or Ten-bit interfaces may also be necessary.  See mii(4).

DESCRIPTION

     The stge device driver supports the Sundance/Tamarack TC9021 Gigabit Ethernet chip.

     The Sundance/Tamarack TC9021 is found on the D-Link DGE-550T, and the Antares Microsystems Gigabit Ethernet board.  It uses an external PHY
     or an external 10-bit interface.

     The TC9021 supports IPv4/TCP/UDP checksumming in hardware.  The stge driver supports this feature of the chip.  See ifconfig(8) for informa-
     tion on how to enable this feature.

SEE ALSO

     arp(4), ifmedia(4), mii(4), netintro(4), pci(4), ifconfig(8)

HISTORY

     The stge driver first appeared in NetBSD 1.6.

AUTHORS

     The stge driver was written by Jason R. Thorpe <thorpej@NetBSD.org>.

BUGS

     The stge driver does not support the VLAN tag insertion/removal feature of the TC9021 chip.  This is primarily because the TC9021's VLAN do
     not have a useful programming interface.

     The stge driver does not yet support jumbo Ethernet frames.

     The stge driver does not yet function properly with 1000BASE-T fitted boards.  Currently, only 1000BASE-SX boards work.

BSD
								   July 24, 2001							       BSD