Hi,
I have broken my laptop hard drive so I would like to put it in an external box to backup my documents.
I have a doubt whether the interface of the hard disk is sata or ide.
Inside notes attached, is reported "controller SATA AHCI" but on the model section is given IDE hard disk
Hi experts,
I need to determine if I have 4GB free space on my UNix server? Is there a way that I can do it instead of executing df -k . in each folder?
Thanks for your help. (3 Replies)
:eek: I use this Solaris to run CMS a call acounting software package for my job. No one could run reports today because it said the this when you logged on
"The following file systems are low, and could adversely affect server performance:
File system /: 99%full"
Can some one please explain... (9 Replies)
Hi,
I can't make the network connection. The cable and hub should be fine since they are working on other systems. I've used 'mktcpip' as well as 'smit tcpip' to configure the interface, and was able to ping the system itself, but I can not ping the gateway - no response. After reboot, the IP... (1 Reply)
Hi,
I have a failed hard disk in my Sun Fire V240. Unfortunately it does not show up in 'cfgadm -al' or in the format command so I cannot unconfigure it and illuminate the blue light on the front to identify it. Is there any way of iluminating the blue lights on the other disks so I can at... (3 Replies)
hi
I've a fresh installation of SCO 5.0.7 on the IDE hard disk.
For SCSI hard disk I can declare, for example blc disk driver using:
# mkdev hd 0 SCSI-0 0 blc 0but it works for IDE hard disk? (3 Replies)
Hi all,
I'm kind of new to programming in Linux & c/c++. I'm currently writing a FileManager using Ubuntu Linux(10.10) for Learning Purposes. I've got started on this project by creating a loopback device to be used as my virtual hard disk. After creating the loop back hard disk and mounting it... (23 Replies)
Good Evening,
2 years ago, I set up an Ubuntu file-server for a friend, who is a photograph amateur. Basically, the server offers a software RAID-5 that can be accessed remotely from a MAC. Unfortunately, I didn't labeled the hard drives (i.e. which physical drive corresponds to the /dev/sdX... (2 Replies)
Hello,
Currently we have a Oracle X4100 ( Solaris 10 ) server with disk failure. Originally our hardware team thought the disk can be hot-swap, when they stood in front of the server, none of the disk failure LED were on, so now we have no idea which disk is the bad one for replacement.
As... (2 Replies)
I am working on VM host and collecting data to identify the type of storage attached to the server which will be migrated to VNX.
it has one ldom created on it
luxadm probe output ---
No Network Array enclosures found in /dev/es
Found Fibre Channel device(s):
Node... (7 Replies)
Discussion started by: kpatel786
7 Replies
LEARN ABOUT NETBSD
pciide
PCIIDE(4) BSD Kernel Interfaces Manual PCIIDE(4)NAME
pciide -- PCI IDE disk controllers driver
SYNOPSIS
pciide* at pci? dev ? function ? flags 0x0000
pciide* at pnpbios? index ?
DESCRIPTION
The pciide driver supports the PCI IDE controllers as specified in the "PCI IDE controller specification, revision 1.0" draft, and provides
the interface with the hardware for the ata driver. Please use the chip-specific drivers for the following controllers for enhanced and DMA
support:
- Acard ATP850 (Ultra/33) and ATP860 (Ultra/66) IDE Controllers: acardide(4)
- Acer labs M5229 IDE Controller: aceride(4)
- Advanced Micro Devices AMD-756, 766, and 768 IDE Controllers: viaide(4)
- Advanced Micro Devices Geode IDE Controllers: geodeide(4)
- CMD Tech PCI0643, PCI0646, PCI0648, and PCI0649 IDE Controllers: cmdide(4)
- Contaq Microsystems/Cypress CY82C693 IDE Controller: cypide(4)
- HighPoint HPT366 Ultra/66, HPT370 Ultra/100, HPT372, and HPT374 Ultra/133 IDE controller: hptide(4)
- Intel PIIX, PIIX3, and PIIX4 IDE Controllers: piixide(4)
- Intel i31244 Serial ATA controller: artsata(4)
- Intel 82801 (ICH/ICH0/ICH2/ICH3/ICH4/ICH5/ICH6) IDE Controllers: piixide(4)
- Intel SCH IDE Controllers: schide(4)
- NVIDIA nForce/nForce2 IDE Controllers: viaide(4)
- OPTi 82c621 (plus a few of its derivatives) IDE Controllers: optiide(4)
- Promise PDC20246 (Ultra/33), PDC20262 (Ultra/66), PDC20265/PDC20267 (Ultra100), PDC20268 (Ultra/100TX2 and Ultra/100TX2v2),
Ultra/133, Ultra/133TX2 and Ultra/133TX2v2 PCI IDE controllers: pdcide(4)
- Serverworks K2 SATA controllers: svwsata(4)
- Silicon Image 0680 IDE controller: cmdide(4)
- Silicon Image SATALink 3112 Serial ATA controller: satalink(4)
- Silicon Image SteelVine 3124/3132/3531 Serial ATA II controller: siisata(4)
- Silicon Integrated System 5597/5598 IDE controller: siside(4)
- Symphony Labs 82C105 and Winbond W83C553F IDE controller: slide(4)
- VIA Technologies VT82C586, VT82C586A, VT82C596A, VT82C686A, VT8233A, and VT8235 IDE Controllers: viaide(4)
The 0x0001 flag forces the pciide driver to use DMA when there is no explicit DMA mode setting support for the controller but DMA is present.
If the BIOS didn't set up the controller properly, this can cause a machine hang.
The 0x0002 flag forces the pciide driver to disable DMA on chipsets for which DMA would normally be enabled. This can be used as a debugging
aid, or to work around problems where the IDE controller is wired up to the system incorrectly.
SEE ALSO acardide(4), aceride(4), artsata(4), ata(4), atapi(4), cmdide(4), cypide(4), geodeide(4), hptide(4), intro(4), optiide(4), pci(4), pdcide(4),
piixide(4), pnpbios(4), satalink(4), schide(4), siisata(4), siside(4), slide(4), viaide(4), wd(4), wdc(4)BSD November 7, 2010 BSD