I am trying to get an old Ultra 45 to boot and it is stuck in a loop. I cannot get anything to come up on a monitor, so when I hook up a serial connection to the TTYa interface I see the following output:
Code:
@(#)OBP 4.21.2 2005/12/22 17:17 Sun Ultra 45 Workstation
Clearing TLBs
Loading Configuration
Membase: 0000.0012.0000.0000
MemSize: 0000.0000.8000.0000
Init CPU arrays Done
Init E$ tags Done
Setup TLB Done
MMUs ON
Init Fire JBUS Control Register...
Block Scrubbing Done
Find dropin, Copying Done, Size 0000.0000.0000.72a0
PC = 0000.07ff.f000.61b8
PC = 0000.0000.0000.6268
Find dropin, (copied), Decompressing
RED State Exception
Error enable reg: 0000.0000.0000.0000
CPU 0000.0000.0000.0001 AFSR 0230.02ae.00c0.0110 JETO Multiple PRIV UCU CPU WDU EDU UE CE
AFAR 0000.0012.7ff0.44f0
CPU: 0000.0000.0000.0001
TL=0000.0000.0000.0005 TT=0000.0000.0000.0064
TPC=0000.0000.4200.4c80 TnPC=0000.0000.4200.4c84 TSTATE=0000.0000.1504.1402
TL=0000.0000.0000.0004 TT=0000.0000.0000.0064
TPC=0000.0000.4200.4c80 TnPC=0000.0000.4200.4c84 TSTATE=0000.0000.1504.1402
TL=0000.0000.0000.0003 TT=0000.0000.0000.0064
TPC=0000.0000.4200.4c80 TnPC=0000.0000.4200.4c84 TSTATE=0000.0000.1504.1402
TL=0000.0000.0000.0002 TT=0000.0000.0000.0064
TPC=0000.0000.4200.0200 TnPC=0000.0000.4200.0204 TSTATE=0000.0000.1500.1502
TL=0000.0000.0000.0001 TT=0000.0000.0000.0010
TPC=0000.0000.0000.6fec TnPC=0000.0000.0000.6ff0 TSTATE=0000.0000.1500.1502
CPU 0000.0000.0000.0001 AFSR 0020.0080.0040.0003 Multiple CPU
AFAR 0000.0012.7ff0.44f0
CPU 0000.0000.0000.0000 AFSR 00b0.0001.0100.0000 JEIC Multiple PRIV RUE
AFAR 0000.0012.7ff0.44e0
reset reason: 0000.0000.0000.0005
It just keeps repeating this over and over, any ideas of what the issue is ? Thanks.
Last edited by Franklin52; 01-14-2014 at 03:17 AM..
Reason: Please use code tags
Hello all! I am praying someone can help me. I have been trying to install dual nics on my FreeBSD box. In my attempts I edited my RC.CONF file. I must have editing something wrong, because during the boot sequence, my machine gets through bringing up most of the services then it stops and gets... (5 Replies)
I just was given an Ultra 60 that I'm trying to get started so that I can re-load the system with Solaris 10. I can't seem to get the system to boot past the initial memory check. I've tried to do an Stop-A to get to the eeprom, but can't do that. My next step is to try to send a break from the... (0 Replies)
Hi All,
Any idea why i'm having this warning during boot:
WARNING: /pci@1f,0/pci@1,1/ide@3/dad@1,0 (dad1):
corrupt label - wrong magic number
This happens after I added another ide HD and reinstall it from solaris 10 to solaris 8.
Thanks in advance. (7 Replies)
Hi all.
I am seeing in one of our less-used servers that it crashed and now won't restart. I get the message 'continue with normal startup or boot into maintenance mode'.
I go into maintenance and run fsck on /usr0 (mentioned in error at restart) it then reboots but goes right back to... (3 Replies)
Folks;
My SUN Ultra 10 5.9 won't boot. It only stops after counting the memory on the white screen then hangs there with nothing. even the power button won't take it down from there, i had to unplug it then re-plug it again.
i inserted a disk with Solaris 9 iso trying to rebuild it but nothing... (1 Reply)
Hi,
I just got a new Ultra 5 and replaced the CD-ROM with an LG DVD-ROM (approved and listed in Sun HCL). Got the DVD-ROM installed to install Solaris 10. Im just learning and new to Solaris installation.
When I insert a Solaris 10 DVD I see that it gets mounted and File Manager opens and... (8 Replies)
HI everyone,
Nice to meet you all.
I recently rebooted Slackware 12.1 running on a Dell PowerEdge 2400. after 240 days of continuous run-time, and discovered it gets stuck in a sbin/agetty loop. We were rebooting because trying to mount root in webmin broke a bunch of things. Couldn't even get... (3 Replies)
Hi all,
I've got a Sun ultra 30 workstation. the Nvram battery died so I replaced it. I reprogrammed the mac address using the mlpl command all that so it booted without error. But for some reason I was trying to boot via the network. So I did a STOP A and boot disk1 which is the alias for my SCSI... (2 Replies)
Hi all,
I've just replaced the eprom battery on my Sun Ultra-30 and having boot issues. For some reason its trying to boot off the network instead of the DISK1. Howe can I change it so the open boot does not default to the boot device: NET
Thanks,
Rob (3 Replies)
Discussion started by: robbo007
3 Replies
LEARN ABOUT NETBSD
pciide
PCIIDE(4) BSD Kernel Interfaces Manual PCIIDE(4)NAME
pciide -- PCI IDE disk controllers driver
SYNOPSIS
pciide* at pci? dev ? function ? flags 0x0000
pciide* at pnpbios? index ?
DESCRIPTION
The pciide driver supports the PCI IDE controllers as specified in the "PCI IDE controller specification, revision 1.0" draft, and provides
the interface with the hardware for the ata driver. Please use the chip-specific drivers for the following controllers for enhanced and DMA
support:
- Acard ATP850 (Ultra/33) and ATP860 (Ultra/66) IDE Controllers: acardide(4)
- Acer labs M5229 IDE Controller: aceride(4)
- Advanced Micro Devices AMD-756, 766, and 768 IDE Controllers: viaide(4)
- Advanced Micro Devices Geode IDE Controllers: geodeide(4)
- CMD Tech PCI0643, PCI0646, PCI0648, and PCI0649 IDE Controllers: cmdide(4)
- Contaq Microsystems/Cypress CY82C693 IDE Controller: cypide(4)
- HighPoint HPT366 Ultra/66, HPT370 Ultra/100, HPT372, and HPT374 Ultra/133 IDE controller: hptide(4)
- Intel PIIX, PIIX3, and PIIX4 IDE Controllers: piixide(4)
- Intel i31244 Serial ATA controller: artsata(4)
- Intel 82801 (ICH/ICH0/ICH2/ICH3/ICH4/ICH5/ICH6) IDE Controllers: piixide(4)
- Intel SCH IDE Controllers: schide(4)
- NVIDIA nForce/nForce2 IDE Controllers: viaide(4)
- OPTi 82c621 (plus a few of its derivatives) IDE Controllers: optiide(4)
- Promise PDC20246 (Ultra/33), PDC20262 (Ultra/66), PDC20265/PDC20267 (Ultra100), PDC20268 (Ultra/100TX2 and Ultra/100TX2v2),
Ultra/133, Ultra/133TX2 and Ultra/133TX2v2 PCI IDE controllers: pdcide(4)
- Serverworks K2 SATA controllers: svwsata(4)
- Silicon Image 0680 IDE controller: cmdide(4)
- Silicon Image SATALink 3112 Serial ATA controller: satalink(4)
- Silicon Image SteelVine 3124/3132/3531 Serial ATA II controller: siisata(4)
- Silicon Integrated System 5597/5598 IDE controller: siside(4)
- Symphony Labs 82C105 and Winbond W83C553F IDE controller: slide(4)
- VIA Technologies VT82C586, VT82C586A, VT82C596A, VT82C686A, VT8233A, and VT8235 IDE Controllers: viaide(4)
The 0x0001 flag forces the pciide driver to use DMA when there is no explicit DMA mode setting support for the controller but DMA is present.
If the BIOS didn't set up the controller properly, this can cause a machine hang.
The 0x0002 flag forces the pciide driver to disable DMA on chipsets for which DMA would normally be enabled. This can be used as a debugging
aid, or to work around problems where the IDE controller is wired up to the system incorrectly.
SEE ALSO acardide(4), aceride(4), artsata(4), ata(4), atapi(4), cmdide(4), cypide(4), geodeide(4), hptide(4), intro(4), optiide(4), pci(4), pdcide(4),
piixide(4), pnpbios(4), satalink(4), schide(4), siisata(4), siside(4), slide(4), viaide(4), wd(4), wdc(4)BSD November 7, 2010 BSD
01-13-2014
? Thanks.