Hi I was trying to mount my USB flashdrive on solaris 10 and I am getting the message saying that (I have already gone through the previous blogs in the forum)
mount: Block device required.
I have tried most of the possible ways.
#rmformat(gives me the necessary information about my flash... (1 Reply)
Hi all
A couple of new M5000 servers will be arriving soon and I need to work out how to configure the underlying domains.
It will come with 4 x CPUS, 32 Gb of memory, 4 x HD, 2 x IOtrays.
Reading the XSCF manual, I can configure the item into 2 domains, something about uni / quad xsb.... (9 Replies)
My previous post seems to be erased and I didn't get any help. I'm logged as root now but no mounting command seems to work, I've tried:
Mount -t vfat /dev/sdc1 /mnt/USB
Changing "sdc1" for hda1-7, and sdc1-7, and still nothing. Sometimes i get:
"special device not found" and others "device... (4 Replies)
I am very new to Solaris.
The machine I am working with is running Solaris 10.
I have a 1.5 TB hard drive plugged into a USB dock plugged into the Solaris machine. I ran 'cfgadm -al' and can see that the usb0/1 is usb-storage that was not there before.
How do i mount this drive and format... (3 Replies)
Hi, I've got an issue here: After I logon to the xscf prompt of this Sun M5000 and did 'XSCF> version -c xcp', the xscf prompt disappeared. I can't get it back and can't log out.
exit
rebootxscf
logout
#.
#>
#>
~#
~#
exit
sendbreak
exit
I tried to set the Mode Switch to the service... (3 Replies)
Hi,
I've configured this Sun M5000 to use two system domains (added a second domain to it). The following is the info about the settings. The showdevices command can't show devices on domain 1 because Solaris is not loaded on it yet.
My question: How can I confirm the hardware devices such as... (5 Replies)
Hi,
I would appreciate some help.
I remotely access, across a VPN, an M5000 and when I connect to the XSCF I can then access the OS using console -d0 and then I can get to the console.
The problem I have is that I need to run something which will take many hours and I can't run it in the... (6 Replies)
Hi all,
I'm developing a short program to look-up for all devices connected to the computer. Using udev and libusb libraries I achieved some progress but I can not find the way to find the mount point.
For instance, given a device that I can retrieve using libusb, I would like to know... (4 Replies)
Hi,
I'm planning to upgrade the XSCF firmware on an M5000, and have a question regarding the OBP part of the upgrade. At the moment, the system looks like this:
XCP0 (Current): 1100
OpenBoot PROM : 02.18.0000
XSCF : 01.10.0000
root@server01 # /usr/sbin/prtconf -V
OBP 4.24.15... (3 Replies)
I took over an M5000 and have a jumper server with a nic to connect to the console IP of an M5000. access via ssh user@ip.
it was working fine, another person can connect remotely on the subnet, but when I ssh,it just hangs and then times out.
so my question is,
any ideas of what I might... (4 Replies)
Discussion started by: rrodgers
4 Replies
LEARN ABOUT NETBSD
url
URL(4) BSD Kernel Interfaces Manual URL(4)NAME
url -- Realtek RTL8150L USB Ethernet driver
SYNOPSIS
url* at uhub?
urlphy* at mii?
DESCRIPTION
The url driver provides support for USB Ethernet adapters based on the Realtek RTL8150L USB-ether bridge chip.
The url driver supports the following adapters:
CompUSA USBKR100
GreenHouse GH-USB100B
Melco Inc. LUA-KTX
Sitecom LN013
For more information on configuring this device, see ifconfig(8).
DIAGNOSTICS
url%d: watchdog timeout A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the
transmission before a timeout expired.
url%d: no memory for rx list The driver failed to allocate an mbuf for the receiver ring.
SEE ALSO arp(4), mii(4), netintro(4), usb(4), ifconfig(8)HISTORY
The url device driver first appeared in NetBSD 1.6.
AUTHORS
The url driver was written by Shingo WATANABE <nabe@nabechan.org>.
BSD September 18, 2006 BSD