Adding a network interface to a bonded interface Post: 302792073

9 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Adding an interface to solaris?

I have a quad ethernet card in my sun box, and only 3 of them are visable when I "ifconfig -a". How do I activate the the 4th one? I think it is solaris 5.6. Thanks. Marc

2. HP-UX

Adding virtual Interface on HP UX

Hello all, I want to add a new virtual interface on HP-UX B.11.11 U 9000/800 box. I know that ifconfig can be used to add the Virtual interface. BUt i do not know the exact syntax. it some times gives plumb error if i try to add # ifconfig vif0 10.1.10.1 up plumb error: No such file...

3. Solaris

Adding Loopback Interface

Hello, I have a SunOS (5.5.1) system that I need to migrate to a new IP address. I would like to have any requests destined for the old IP to be forwarded to this server. One suggestion I had was to add a route on my router that would point the old IP to the new IP. How do I add another...

4. Red Hat

Netdump over bonded interface ?

Netdump over bonded interface ? Hey there,.. I have heard from admins, that netdump usually fails over a bonded network interface. I have written a multi-OS checkdump script , which checks if the respective crashdump utility on corresponding OS is correctly configured, space is available,...

5. Solaris

Network interface down after adding static route

Please , I have a problem I have add a statis route on Solaris 10, but after this, the network interface of Server was Offline. The system is in cluster mode (3.2) route add -net 10.10.1.128 -netmask 255.255.255.128 10.10.1.51 ------------------- lo0:...

6. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI...

7. SCO

Change SCO - GUI or Desktop interface to DOS based interface

Hi all I have installed a demo version of SCO OpenServer 5.0.2, I finally found it is Desktop Interface, I would like to know how to change its interface to dos based interface? If you have any ideas, please tell me then. Thank you

8. IP Networking

Need a bridge from an ethernet interface to a serial interface

This is my situation DOS pc serial cable (sl0) Linux Pc eth1 192.168.0.10 <-------------------->192.168.0.2 <------------>192.168.0.1 (router) I connected the linux pc and the dos pc with a SLIP (serial line internet protocol), so they can communicate in the sl0 interface. ...

9. AIX

Is it possible to configure bonding over bonded interface in AIX?

Hi Everyone, Is it possible to configure bonding over bonded interface in AIX? For example: server has for NIC port: ent0 ent1 ent2 ent3 First I create a EtherChannel ent4 from ent0 and ent1. and then I create a EtherChannel ent5 from ent2 and ent3. Can I create a EtherChannel...

LEARN ABOUT NETBSD

urlphy

URL(4)							   BSD Kernel Interfaces Manual 						    URL(4)

NAME

     url -- Realtek RTL8150L USB Ethernet driver

SYNOPSIS

     url*    at uhub?
     urlphy* at mii?

DESCRIPTION

     The url driver provides support for USB Ethernet adapters based on the Realtek RTL8150L USB-ether bridge chip.

     The url driver supports the following adapters:

	   CompUSA USBKR100
	   GreenHouse GH-USB100B
	   Melco Inc. LUA-KTX
	   Sitecom LN013

     For more information on configuring this device, see ifconfig(8).

DIAGNOSTICS

     url%d: watchdog timeout  A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the
     transmission before a timeout expired.

     url%d: no memory for rx list  The driver failed to allocate an mbuf for the receiver ring.

SEE ALSO

     arp(4), mii(4), netintro(4), usb(4), ifconfig(8)

HISTORY

     The url device driver first appeared in NetBSD 1.6.

AUTHORS

     The url driver was written by Shingo WATANABE <nabe@nabechan.org>.

BSD
								September 18, 2006							       BSD