Adding an interface to solaris?


 
Thread Tools Search this Thread
Top Forums UNIX for Dummies Questions & Answers Adding an interface to solaris?
# 1  
Question

I have a quad ethernet card in my sun box, and only 3 of them are visable when I "ifconfig -a". How do I activate the the 4th one? I think it is solaris 5.6. Thanks.

Marc
# 2  
I beleivethat ifconfig -a only shows configured interfaces. Though I am not certain that this will work, try creating a file named /etc/hostname.qe3 containing the hostname of that interface. (This assumes that qe0,qe1 & qe2 are present) Use ifconfig to give it an IP and add the entry to /etc/hosts.
 

Previous Thread | Next Thread
Thread Tools Search this Thread
Search this Thread:
Advanced Search

Test Your Knowledge in Computers #296
Difficulty: Easy
Linux Mint 2.0 was based on Ubuntu 6.10 and used the Ubuntu 6.10 package repositories and using it as a codebase.
True or False?

8 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Adding a network interface to a bonded interface

I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies

2. Solaris

Network Interface -- Solaris

Dear All, I have a solaris Server in which I have 4 network interfaces , out of which only one is used . So all the applications are using this interface . The interface speed is 1000Mbps . I find no hardware issue or packets g being dropped. But i find that no of Input and Output... (4 Replies)
Discussion started by: jegaraman
4 Replies

3. Solaris

Command line Interface or GUI Interface not shown on solaris

Dear all, I am a newbie in solaris and I need your advice. I have a Solaris version 5.9 installed on Sunfire V240. I am able to ssh the machine from putty remotely. My problem is that I cannot see the display from KVM switch I have connected to it. I need also to be able to see the GUI... (2 Replies)
Discussion started by: mbouster
2 Replies

4. Solaris

Network interface down after adding static route

Please , I have a problem I have add a statis route on Solaris 10, but after this, the network interface of Server was Offline. The system is in cluster mode (3.2) route add -net 10.10.1.128 -netmask 255.255.255.128 10.10.1.51 ------------------- lo0:... (1 Reply)
Discussion started by: Ruggero
1 Replies

5. Solaris

sppp0 interface in solaris 10

What is sppp0 interface in solaris 10 and how can we disable it ? (1 Reply)
Discussion started by: fugitive
1 Replies

6. Solaris

Adding Loopback Interface

Hello, I have a SunOS (5.5.1) system that I need to migrate to a new IP address. I would like to have any requests destined for the old IP to be forwarded to this server. One suggestion I had was to add a route on my router that would point the old IP to the new IP. How do I add another... (2 Replies)
Discussion started by: reiklen
2 Replies

7. IP Networking

Activating an interface on a Solaris 10

Help! How do I get (configure) an inteface up in order to get access to the internet? System in use is SPARC Ultra 5 - it worked before but not now when I re-installed the system and forgot to connect the RJ45 cable to the interface. (3 Replies)
Discussion started by: Maen
3 Replies

8. HP-UX

Adding virtual Interface on HP UX

Hello all, I want to add a new virtual interface on HP-UX B.11.11 U 9000/800 box. I know that ifconfig can be used to add the Virtual interface. BUt i do not know the exact syntax. it some times gives plumb error if i try to add # ifconfig vif0 10.1.10.1 up plumb error: No such file... (3 Replies)
Discussion started by: supersumanth
3 Replies

Featured Tech Videos