10-22-2012
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have been asked to research Jumpstart and don't know where to begin! Any ideas would be much appreciated! Thanks! :-) (1 Reply)
Discussion started by: avana100
1 Replies
2. UNIX for Dummies Questions & Answers
Hi,
Which sites have general information on JumpStart for Solaris 8?
I would like to know more about boot server, installation server, and configuration server.... and all other good things about JumpStart....Thanks..:p
Doo... (2 Replies)
Discussion started by: dookeobih
2 Replies
3. UNIX for Advanced & Expert Users
HI.
i was wondering if you can jumpstart using the solaris intel platform? please help thanks (3 Replies)
Discussion started by: souldier
3 Replies
4. Solaris
Hello all,
I configured a jumpstart server ( the server is in the same subnet as the client) and gave boot net - install in the client.
The client boots up shows the banner and then displays error:
cant read disk label
cant open disk label package
and then goes to OK prompt.
What... (1 Reply)
Discussion started by: Pratik Gharti
1 Replies
5. Solaris
Ever since I have started using Solaris 10 images, I have had a problem I can not find a solution for.
I have a Solaris 10 image that I created from a Solaris 10 DVD. The sysidcfg file has been created and set up in the bootparams file.
I have no issues in Solaris 8 or 9. In Solaris 10, the... (5 Replies)
Discussion started by: rsherry
5 Replies
6. Solaris
I found my issues were resolved via instructions, from, information, via the url:
Preconfiguring With the sysidcfg File (Solaris 10 8/07 Installation Guide: Network-Based Installations) - Sun Microsystems
Also, sysidcfg, rules etc, ought be in the correct place. The documents that were not bad,... (1 Reply)
Discussion started by: solaris12345
1 Replies
7. Homework & Coursework Questions
Q. Write a script that behaves both in interactive and non interactive mode. When no arguments are supplied it picks up each C program from the directory and prints first 10 lines.
It then prompts for deletion of the file.
If user supplies arguments with the script , then it works on those files... (1 Reply)
Discussion started by: rits
1 Replies
8. Homework & Coursework Questions
Q. Write a script that behaves both in interactive and non interactive mode. When no arguments are supplied it picks up each C program from the directory and prints first 10 lines.
It then prompts for deletion of the file.
If user supplies arguments with the script , then it works on those files... (8 Replies)
Discussion started by: rits
8 Replies
9. Solaris
client boots fine, it gets the ip 192.168.0.10 and the bootfile. Then there is :
SunOS 5.10 Version Generic_141445-09 32-bit"
...
Configuring devices.
Custom JumpStart
Reading ZFS config: done
Setting up Java. Please wait ...
NOTE: Not enough memory for graphical installation. Graphical... (4 Replies)
Discussion started by: TomSu
4 Replies
10. Homework & Coursework Questions
1.) I am to write scripts that will be phasetest folder in the home directory.
2.) The folder should have a set-up,phase and display files
I have written a small script which i used to check for the existing users and their password.
What I need help with:
I have a set of questions in a... (19 Replies)
Discussion started by: moraks007
19 Replies
LEARN ABOUT NETBSD
urlphy
URL(4) BSD Kernel Interfaces Manual URL(4)
NAME
url -- Realtek RTL8150L USB Ethernet driver
SYNOPSIS
url* at uhub?
urlphy* at mii?
DESCRIPTION
The url driver provides support for USB Ethernet adapters based on the Realtek RTL8150L USB-ether bridge chip.
The url driver supports the following adapters:
CompUSA USBKR100
GreenHouse GH-USB100B
Melco Inc. LUA-KTX
Sitecom LN013
For more information on configuring this device, see ifconfig(8).
DIAGNOSTICS
url%d: watchdog timeout A packet was queued for transmission and a transmit command was issued, however the device failed to acknowledge the
transmission before a timeout expired.
url%d: no memory for rx list The driver failed to allocate an mbuf for the receiver ring.
SEE ALSO
arp(4), mii(4), netintro(4), usb(4), ifconfig(8)
HISTORY
The url device driver first appeared in NetBSD 1.6.
AUTHORS
The url driver was written by Shingo WATANABE <nabe@nabechan.org>.
BSD
September 18, 2006 BSD