03-08-2012
Access to network interface (Mac-network)
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. AIX
Hi every body,
I have a Fiber Channel interface (fcs2) in AIX 5.2. This interface was fine & up but for some reason I could not return this interface UP again after I set it DOWN.
When I tried to set this interface UP I encountered the following error:
Method error... (7 Replies)
Discussion started by: aldowsary
7 Replies
3. UNIX for Advanced & Expert Users
Hi all,
I'm using an HP Proliant server with double NIC and Debian 5 (Lenny) as its OS. I used link bonding on it for several years with no problem.
Today, (now only one interface connected to switch) the interface went down. I restarted networking service (/etc/init.d/networking restart) and... (7 Replies)
Discussion started by: mjdousti
7 Replies
4. Solaris
HI,
genunix: NOTICE: ce0: xcvr addr:0x01 - link up 100 Mbps half duplex
genunix: WARNING: ce0: fault detected external to device; service degraded
genunix: WARNING: ce0: xcvr addr:0x01 - link down
genunix: NOTICE: ce0: fault cleared external to device; service available
genunix: ... (4 Replies)
Discussion started by: sunnybee
4 Replies
5. Solaris
i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ..how ?
Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies
6. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
7. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
8. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
9. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
CNW(4) BSD Kernel Interfaces Manual CNW(4)
NAME
cnw -- Netwave AirSurfer wireless network driver
SYNOPSIS
cnw* at pcmcia? function ?
DESCRIPTION
The cnw interface provides access to a theoretical 1 Mb/s wireless Ethernet network based on the Netwave AirSurfer Wireless LAN (formerly
known as the Xircom Netwave Wireless LAN).
Note that the driver does not support newer devices such as the Netwave AirSurfer ``Plus'', or the BayStack 650/660. These devices are sup-
ported by the awi(4) driver.
Netwave devices are not compatible with IEEE 802.11 wireless networks. Also note that there are Netwave devices with different wireless fre-
quency, depending on the radio band plan in each country.
The card uses 36K of I/O memory mapped to the card. You may need to increase memory space available to the PCMCIA controller. See pcmcia(4)
for details.
In use, the cards appear to achieve up to a 420Kb/s transfer rate, though a transfer rate between 250Kb/s and 350Kb/s is typical.
The card operates in the 2.4GHz frequency range and is subject to interference from microwaves, IEEE 802.11 wireless network devices, as well
as earth. For example, it seems that IEEE 802.11 channel 14 conflicts with Netwave (US frequency). They interfere with each other if they
are both operated in the same geographic region, causing weird packet loss. You may be able to avoid the interference with IEEE 802.11
devices, by changing the IEEE 802.11 channel.
HARDWARE
Cards supported by the cnw driver include:
Xircom CreditCard Netwave
NetWave AirSurfer
DIAGNOSTICS
cnw0: can't map memory Indicates that the driver was not able to allocate enough PCMCIA bus address space into which to map the device. See
pcmcia(4) and increase memory available to the PCMCIA controller.
SEE ALSO
arp(4), awi(4), inet(4), intro(4), pcmcia(4), cnwctl(8)
BSD
January 5, 1997 BSD