Don't enter or alter any gateways or other routing information.
No routing whatsoever is needed to talk over a point-to-point link, or over the local subnet -- routing and gateways only get involved for things beyond the local network.
All that's needed for two computers connected loopback to ping each other, for instance, is:
The OS will automatically pick the right interface for local traffic based on IP address and subnet mask.
Here's the problem. I got one network with a internett connection (2mbit). In this network there's 5 computers connected together with a hub. The other network is also with 5 computers. I'm just wondering if I could connect these networks together. But the one network should not get access to the... (1 Reply)
Hello,
I've moved to a new network with multiple AIX box's. Most of them are working fine and dandy.
On one box I need to set up a static route to a gateway.. no problem right?
Whenever I add the route it appears in the routing table as UGc and then begins adding new entries to the... (1 Reply)
I have an IP routing issue or I am just to stupid to work it out myself.
I have setup am old PC running SUSE Linux 11.3 as a router, the system has 3 Interfaces connecting 3 networks.
Interface 1 = 10.164.2.161/21
Interface 2 = 192.168.1.210/24
Interface 3 = 30.1.0.11/16
The default... (6 Replies)
Hi Mates,
I have one problem connecting a solaris machine to winxp machine.
Setup:-
Solaris 10 OS Virtual machine - on VMWARE (Ip Address:- 192.168.10.3).
WINXP SP2 is the base os. (Ip Address:- 192.168.10.2).
Bothe machines are connected using a bridge networking VMnet1.
When i ping... (1 Reply)
I have run into a wall troubleshooting a Centos 5 networking issue. Hoping someone can assist.
I've got a box with two vlans trunked over bond0
bond0 Link encap:Ethernet HWaddr 00:22:64:C1:D6:60
inet6 addr: fe80::222:64ff:fec1:d660/64 Scope:Link ... (0 Replies)
System: Dell Desktop w/ 2 SATA drives running Ubuntu 9.10 that uses 2 ethernet cards, 1 for internet connectivity and another to interface the machine with a high voltage power supply which supports ssh and EPICS controls. Second Ethernet card is connected to a NetGear WNR3500 router, the VME... (0 Replies)
Hi,
We have a website running on a local centos 5.4 surfer, static IP.
The domain.com uses no-ip.com to take care of the DNS, it forwards all to my server.
My router receives the port 80 call, routes it to my server and the world can see domain.com perfectly fine.
However, we cannot see... (3 Replies)
Hi,
I would like to ask some networking solution regarding my work LAN and 3G usb network problem. I want to route my internet traffic to the 3G network and sometimes connect to some of my work network for ssh to configure some workstation or print something. Currently my problem is i can't... (0 Replies)
we are not able to ping client server (falcon-ebr.sbms.bsc.com) from netbackup master server (135.179.96.122 tsprd-ebr.edc.single.net)
However from client server we are able to ping the master Server.
Please assist on this (1 Reply)
I recently installed Centos 6 and is my SOHO firewall/router. The small network is layout like such:
|--eth0(WAN)
Centos 6(firewall/router)
|---eth1(LAN)
|
Switch
|
|
LAN(192.168.3.0/27)
|
|
PCs ----Laptops---Printer... (8 Replies)
Discussion started by: metallica1973
8 Replies
LEARN ABOUT SUSE
tgt-setup-lun
tgt-setup-lun(8) System Manager's Manual tgt-setup-lun(8)NAME
tgt-setup-lun - creates a target, adds a device to the target and defines initiators that can connect to the target
SYNOPSIS
tgt-setup-lun -d device -n target_name [initiator_IP1 initiator_IP2 ...] [-h]
DESCRIPTION
Starts tgtd if necessary and creates a target according to the supplied target_name. The format of the target name is as follows:
iqn.2001-04.com.<hostname>-<target_name> The target name must be unique.
The script then adds the requested device to the target. If specific IP addresses are defined, it adds them to the list of allowed initia-
tors for that target. If no IP addresses is defined, it defines that the target accepts any initiator.
EXAMPLES
Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81:
tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81
Create a target that uses /dev/sdb1 and allows connections only from 192.168.10.81 and 192.168.10.82:
tgt-setup-lun -d /dev/sdb1 -n my_target 192.168.10.81 192.168.10.82
Create a target that uses /dev/sdb1 and allows connections from any initiator:
tgt-setup-lun -d /dev/sdb1 -n my_target
Display help:
tgt-setup-lun -h
AUTHOR
Written by Erez Zilber
REPORTING BUGS
Report bugs to <erezz@voltaire.com>.
COPYRIGHT
Copyright (C) Voltaire Ltd. 2008.
tgt-setup-lun(8)