07-19-2011
jlliagre,
Thanks for the info. I will have to look into exclusive IP zones. Can you tell me the disadvantages of the way I do it. This way I can learn from you.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi !
Does anyone know how can i get information about my network interface ... if it works in half or full duplex mode !!
Thx in adivance !
Witt (4 Replies)
Discussion started by: witt
4 Replies
2. UNIX for Advanced & Expert Users
Hi expert,
Need some help on network interface issue..
I have added 2 x NIC card onto the Ultra 2 system recently and configured as hme1 and hme2. I have unconfigured the onboard hme0 network interface and it was running fine till few days later, i keep recieving error messages showing hme0... (6 Replies)
Discussion started by: sc2005
6 Replies
3. Red Hat
Hi
I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest.
Thanks
Ankur (2 Replies)
Discussion started by: ankurk
2 Replies
4. Solaris
Hi,
I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface.
Please advise how to configure network interfaces using VMware. (1 Reply)
Discussion started by: ajhal04
1 Replies
5. UNIX and Linux Applications
Hi,
I'm a italian student. For my thesis I develop a gateway with protocol 6lowpan.
For that I must access to network interface to develope my personal stack based on standard 802.15.4.
Can you help me? I need an explanation for that. (0 Replies)
Discussion started by: berny88
0 Replies
6. IP Networking
Hello,
Please what's the difference between:
AND
Thank you so much (3 Replies)
Discussion started by: chercheur857
3 Replies
7. IP Networking
Hello,
Please, how can i create a network interface with a routable IP address on linux (ubuntu) ?
AND
How can i desactivate an interface?
Thank you so much for help. (1 Reply)
Discussion started by: chercheur857
1 Replies
8. Solaris
I've one Netra 240
After changing main board and system configuration card reader, Network is not accessible any more, Network interfaces are always UP and Running even when there is no cable connected to Network interfaces.
I tried to restart and plumb/unplumb with no luck.
ifconfig -a... (7 Replies)
Discussion started by: samer.odeh
7 Replies
9. UNIX for Dummies Questions & Answers
I have a RHEL 5 system with a bonded interface configure using only one network port (eth0). So I have config file for ifcfg-bond0 and ifcfg-eth. I'd like to configure eth5 to be the second SLAVE in the bond. My question is, after I modify ifcfg-eth5, can I add eth5 to the bond0 interface without... (1 Reply)
Discussion started by: westmoreland
1 Replies
10. Solaris
I have a few non-globa zones running in a 10.10.xx.xx network on a machine that is on a 192.168.xx.xx network.
My goal is to allow each of the non-global zones to communicate to each other while not communicating on the 192.168.xx.xx network.
I am using the current version of Solaris 10 in... (7 Replies)
Discussion started by: BradJM
7 Replies
LEARN(1) General Commands Manual LEARN(1)
NAME
learn - computer aided instruction about UNIX
SYNOPSIS
learn [ -directory ] [ subject [ lesson ] ]
DESCRIPTION
Learn gives Computer Aided Instruction courses and practice in the use of UNIX, the C Shell, and the Berkeley text editors. To get started
simply type learn. If you had used learn before and left your last session without completing a subject, the program will use information
in $HOME/.learnrc to start you up in the same place you left off. Your first time through, learn will ask questions to find out what you
want to do. Some questions may be bypassed by naming a subject, and more yet by naming a lesson. You may enter the lesson as a number
that learn gave you in a previous session. If you do not know the lesson number, you may enter the lesson as a word, and learn will look
for the first lesson containing it. If the lesson is `-', learn prompts for each lesson; this is useful for debugging.
The subject's presently handled are
files
editor
vi
morefiles
macros
eqn
C
There are a few special commands. The command `bye' terminates a learn session and `where' tells you of your progress, with `where m'
telling you more. The command `again' re-displays the text of the lesson and `again lesson' lets you review lesson. There is no way for
learn to tell you the answers it expects in English, however, the command `hint' prints the last part of the lesson script used to evaluate
a response, while `hint m' prints the whole lesson script. This is useful for debugging lessons and might possibly give you an idea about
what it expects.
The -directory option allows one to exercise a script in a nonstandard place.
FILES
/usr/share/learn subtree for all dependent directories and files
/usr/tmp/pl* playpen directories
$HOME/.learnrc startup information
SEE ALSO
csh(1), ex(1)
B. W. Kernighan and M. E. Lesk, LEARN - Computer-Aided Instruction on UNIX
BUGS
The main strength of learn, that it asks the student to use the real UNIX, also makes possible baffling mistakes. It is helpful, espe-
cially for nonprogrammers, to have a UNIX initiate near at hand during the first sessions.
Occasionally lessons are incorrect, sometimes because the local version of a command operates in a non-standard way. Occasionally a lesson
script does not recognize all the different correct responses, in which case the `hint' command may be useful. Such lessons may be skipped
with the `skip' command, but it takes some sophistication to recognize the situation.
To find a lesson given as a word, learn does a simple fgrep(1) through the lessons. It is unclear whether this sort of subject indexing is
better than none.
Spawning a new shell is required for each of many user and internal functions.
The `vi' lessons are provided separately from the others. To use them see your system administrator.
7th Edition October 22, 1996 LEARN(1)