Configure network interface for Solaris 10

Thread Tools Search this Thread
Operating Systems Solaris Configure network interface for Solaris 10
# 1  
Old 09-14-2011
Configure network interface for Solaris 10


I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface.

Please advise how to configure network interfaces using VMware.
# 2  
Old 09-14-2011
scroll to the bottom of this page and follow the links!
Login or Register to Ask a Question

Previous Thread | Next Thread

9 More Discussions You Might Find Interesting

1. Solaris

Network interface configuration - Solaris 11

Hi, I am new in Solaris 11. I can't even make the NIC work. Here is the issue: Any help will be greatly appreciated. (6 Replies)
Discussion started by: aixlover
6 Replies

2. Solaris

Network Interface -- Solaris

Dear All, I have a solaris Server in which I have 4 network interfaces , out of which only one is used . So all the applications are using this interface . The interface speed is 1000Mbps . I find no hardware issue or packets g being dropped. But i find that no of Input and Output... (4 Replies)
Discussion started by: jegaraman
4 Replies

3. Solaris

configure zones to have different network interface and network

i need to configure a zone to use different interface (bge2) than global and have connected to completely different network switch & to use its own defaultrouter and hosts file .. is it possible ..if so ? Thanks (9 Replies)
Discussion started by: skamal4u
9 Replies

4. Solaris

Getting Network Interface details in solaris

Hi, /sbin/ifconfig -a when i login as guest user , output like below, lo0: flags=2001000849<UP,LOOPBACK,RUNNING,MULTICAST,IPv4,VIRTUAL> mtu 8232 index 1 inet netmask ff000000 eri0: flags=1004843<UP,BROADCAST,RUNNING,MULTICAST,DHCP,IPv4> mtu 1500 index 2 inet... (5 Replies)
Discussion started by: forumguest
5 Replies

5. Solaris

What are the kernel parameter of network interface in Solaris?

Hi gurus Could anybody tell me that what are the kernal parameter of network interface in solaris Regards (3 Replies)
Discussion started by: girish.batra
3 Replies

6. Red Hat

How to configure network interface card in OEL.

Hi I have installed OEL 4 on my dell XPS laptop. But when i connect the LAN cable and try to acesss internet. it does not work. the led's in the port do not blink when i plug in the cable .do i need some drivers please suggest. Thanks Ankur (2 Replies)
Discussion started by: ankurk
2 Replies

7. Solaris

Route new network interface Solaris 8

Hi there, I'm trying to configure an additional network interface on Solaris 8 (eri0). The interface has been activated, but all the frames are still routed to the current default interface (ce0) I've tried following command (with various syntaxes...) unsuccessfully so far: # route add... (2 Replies)
Discussion started by: sreiniche
2 Replies

8. Solaris

how to configure network in solaris 10?

Hi..i have installed solaris 10 on vmware. I m not able connect to internet. pls help in detail. how to solve the problem. During the installation i have put no DHCP. cofigured manually ( Ip default gateway . (3 Replies)
Discussion started by: johnavery
3 Replies

9. Solaris

network interface problem solaris 2.5

Hi guys, Hope somebody can help me on this. I have a Sun Sparc 20 workstation and it has a boot problem. During boot, an error message " ifconfig:socket: Bad File Number" come up and the workstation hang (cannot boot). I did boot -s and checked using ifconfig -a command but i got the same... (0 Replies)
Discussion started by: kroegand
0 Replies
Login or Register to Ask a Question