Login or Register to Ask a Question and Join Our Community

Sponsored Content
Full Discussion: Cannot ping default gateway
Top Forums UNIX for Dummies Questions & Answers Cannot ping default gateway Post 302539254 by Rutgerncas on Friday 15th of July 2011 11:40:03 PM
Old 07-16-2011
Cannot ping default gateway
I have NCR MP-RAS unix. I have been trying for several months to get our network working since we had never used it before. I have setup all routes that I can think of. I know it has something to do with the routing table, because out of sheer luck I was able to get it working, and than like a good ol computer it decided to restart and I lost my changes. Unfortunately I do not know what I changed/added to make it work. Any help would be greatly appreciated. Below is all the information I think you need. Tanks in advance.

Code:
netstat -rn
Destination      Gateway            Flags    Refs      Use  Interface
default          192.168.1.1        UGS         0        0  en2
127.0.0.1        127.0.0.1          UH          2       11  lo0
192.168.1        192.168.1.129      UGS         0        0  en2
192.168.1.129    127.0.0.1          UGHS        1       16  lo0
224              192.168.1.129      UCS         0        0  en2
 
ifconfig -a
en2: flags=4043<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
        inet 192.168.1.129 netmask ffffff00 broadcast 192.168.1.255
        perf. params: recv size: 24576; send size: 24576; full-size frames: 1
        ether 00:00:e2:1d:84:a0
lo0: flags=4049<UP,LOOPBACK,RUNNING,MULTICAST> mtu 8232
        inet 127.0.0.1 netmask ff000000
        perf. params: recv size: 57344; send size: 57344; full-size frames: 1

Last edited by Scott; 01-04-2013 at 02:34 PM.. Reason: Code tags
 

10 More Discussions You Might Find Interesting

1. IP Networking

Unable to ping the gateway IP itself

We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command 64 bytes from 124.168.215.40:... (6 Replies)
Discussion started by: chrisanto_2000
6 Replies

2. IP Networking

Multihomed can not ping gateway

Hello this is my first post at this forum. Apologize for my lack of network understanding but Im posting to learn. I have a problem reaching default gateway 10.18.110.1 If I use my laptop I can ping 10.18.110.1 but with our red hat multihomed server the gateway does not respond to ping. cat... (11 Replies)
Discussion started by: vettec3
11 Replies

3. Solaris

ping -s to default gateway very slow

I was install new solaris10 on m4000 model after that i "ping -s" to default gateway but it's take longtime (2 Min) to reply and if i use "ping" only it's reply to fase(2 sec). any body who can tell me about my problem and how to fix it please. i'm try to fix several days. (2 Replies)
Discussion started by: cesmk
2 Replies

4. AIX

Can not Ping Gateway

Hello, I am new to Unix :D and have been trying to configure an AIX server running 5.3. I used smitty or smit to configure interface 0 on the server. I am able to ping the IP I set, however I am still unable to ping the gateway. I configured the IP by navigating to Communications Applications... (6 Replies)
Discussion started by: cdub50
6 Replies

5. Red Hat

Cannot ping gateway

I know the subject line is very similar to: destination host unreachable but the problem with my machine appears to be somewhat different from that thread. apologies if I missed something from there. We recently moved a machine physically and from one subnet to another . I used... (1 Reply)
Discussion started by: mirage
1 Replies

6. AIX

Cant ping default gateway aix 53 07 new install

I just reinstalled a fresh install of 5300 07 on an old 44p model 170, after installing I set an IP Address on en2 and I tried to the ping default gateway, no response. I tried a startsrc -g tcpip ... and then I can ping the default gateway. I broke the ping and tried again to ping. I cannot... (1 Reply)
Discussion started by: asyed123
1 Replies

7. Red Hat

Can not ping default gateway

Hi, Here is the issue: There are 2 identical systems in the same subnet here. They can ping and ssh each other. One can ping the default gateway and one can not with error '... icmp_seq Destination Host Unreachable'. I can't find any difference between the two systems in terms of network... (4 Replies)
Discussion started by: aixlover
4 Replies

8. AIX

Networking Issue (Cant Ping the gateway)

Hi, I installed AIX 7.1 on a blade though (hmc with vio). I can ping the IP address, but not the gateway. Is there anything that I should configure? Is there anything that I have to check with vio setting or Am I missing any configuration? Please let me know further. Thank you (5 Replies)
Discussion started by: pjeedu2247
5 Replies

9. UNIX for Advanced & Expert Users

Unable to ping default gateway

I have setup a Linux machine on my server but for some reason Im unable to reach my default gateway. This is causing me to not communicate with the outside world (unable to connect to CentOS repos) # ifconfig enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500 inet... (3 Replies)
Discussion started by: Junaid Subhani
3 Replies

10. UNIX for Beginners Questions & Answers

Inconsistency between RedHat 6.5 global gateway and single gateway leads to loss of default gateway

Dear friends I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies

LEARN ABOUT NETBSD

ipw

IPW(4)							   BSD Kernel Interfaces Manual 						    IPW(4)

NAME

     ipw -- Intel PRO/Wireless 2100 IEEE 802.11 driver

SYNOPSIS

     ipw* at pci? dev ? function ?

DESCRIPTION

     The ipw driver provides support for the Intel PRO/Wireless 2100 MiniPCI network adapter.

     The Intel firmware requires acceptance of the End User License Agreement.	The full license text can be found in /lib-
     data/firmware/if_ipw/LICENSE.  The license is agreed to by setting the sysctl variable hw.ipw.accept_eula to 1.

     By default, the ipw driver configures the adapter for BSS operation (aka infrastructure mode).  This mode requires the use of an access
     point.

     For more information on configuring this device, see ifconfig(8).

EXAMPLES

     Join an existing BSS network (i.e.: connect to an access point):

	   ifconfig ipw0 inet 192.168.0.20 netmask 0xffffff00

     Join a specific BSS network with network name ``my_net'':

	   ifconfig ipw0 inet 192.168.0.20 netmask 0xffffff00 nwid my_net

     Join a specific BSS network with 64 bits WEP encryption:

	   ifconfig ipw0 inet 192.168.0.20 netmask 0xffffff00 nwid my_net 
		   nwkey 0x1234567890

     Join a specific BSS network with 128bits WEP encryption:

	   ifconfig ipw0 inet 192.168.0.20 netmask 0xffffff00 nwid my_net 
		   nwkey 0x01020304050607080910111213

DIAGNOSTICS

     ipw%d: device timeout  The driver will reset the hardware.  This should not happen.

SEE ALSO

     an(4), awi(4), pci(4), wi(4), ifconfig(8), ipwctl(8)

     The IPW Web Page, http://damien.bergamini.free.fr/ipw/.

AUTHORS

     The ipw driver and this man page were written by Damien Bergamini <damien.bergamini@free.fr>.

BSD
								 November 7, 2008							       BSD
All times are GMT -4. The time now is 10:37 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy