Sponsored Content
Operating Systems Solaris How to enable hba port of a two port hba card Post 302498482 by rishiraaz on Monday 21st of February 2011 12:51:18 PM
Old 02-21-2011
Code:
fcinfo hba-port

shows three cards
all connected

tried syminq hba

it also shows 3 cards all online

all the three cards are one port cards as far as i found .

is there any command which shows the offline cards ??

Last edited by Yogesh Sawant; 02-25-2011 at 05:01 AM.. Reason: added code tags
 

10 More Discussions You Might Find Interesting

1. Solaris

HBA Card

Hello...I got a problem here. I have HBAs installed in one of the domains in E20 and I gotta find out the brand and firmware. But when I do a prtconf, I cannot see the HBA. For other servers installed with HBAs, when I do prtconf on them I can see either qlc or em. Can you guys enlighten me how to... (5 Replies)
Discussion started by: xiaochensg
5 Replies

2. AIX

Need HBA card driver

Hi All, SUN emulex HBA card has been installed on P520 box. When i run the cfgmgr i am getting the following message. lpar2#cfgmgr cfgmgr: 0514-621 WARNING: The following device packages are required for device support but are not currently installed.... (0 Replies)
Discussion started by: b_manu78
0 Replies

3. IP Networking

4GB Dual Port HBA

I have one 4GB, dual port HBA. Is each port rated for 4GB, or is it the whole HBA rated for 4GB? Also, how do I determine which is port0 / port1 with "lscfg -vl fcs0" command. Thanks. (0 Replies)
Discussion started by: jwholey
0 Replies

4. Solaris

Solaris 10. fcinfo hba-port shows adapter not Found

I understand that fcinfo hba-port should show information(WWN, HBA vendor, etc..) but my result show "No adapter found". If I used grep -i 'version' /var/adm/messages* then I see my installed HBA (QLogic FCode at 2.00.09).. I am wondering why and what I had failed to install? Thanks in advance.... (23 Replies)
Discussion started by: Y4Net
23 Replies

5. Solaris

Few things related to HBA port & fcinfo command

Hi Gurus I need to know few things related to HBA port & fcinfo command I have a server where there are 4 HBA ports cards are their. Out of 4 ports 2 are in use & 2 are not in use when I check it physicall. Now I want to know the command through which I can get information about all above... (6 Replies)
Discussion started by: girish.batra
6 Replies

6. Solaris

How to enable Serial port on ILOM, when Network Port is enabled in parallel

Hi Everyone, In my environment, I have few T5220. On the iLOM Management Card, I have both Network and Serial port are cabled, I don't have any issues while I try to connect using Network Management port, but when I try to connect the serial port for the same server which is actually connected... (3 Replies)
Discussion started by: bobby320
3 Replies

7. Solaris

Which FC HBA card support Solaris9

I have JNI FCE-6460-N fc card , it is detected in OK prompt.....I connected Sun StorEDGE A5000 FC storage. in OK prompt, PROBE-SCSI-ALL showing A5000 fc hdds details in ok prompt..... but in OS level.....not showing the hdd, i tried in DEVFSADM command and FORMAT command not showing A5000... (3 Replies)
Discussion started by: anysystem
3 Replies

8. Red Hat

HBA card faulty

Hi, How to determine if HBA card in getting faulty from linux host ? any pointers. (2 Replies)
Discussion started by: saurabh84g
2 Replies

9. Solaris

How to find port number wwn of particular port on dual port HBA,?

please find the below o/p for your reference bash-3.00# fcinfo hba-port HBA Port WWN: 21000024ff295a34 OS Device Name: /dev/cfg/c2 Manufacturer: QLogic Corp. Model: 375-3356-02 Firmware Version: 05.03.02 FCode/BIOS Version: BIOS: 2.02; fcode: 2.01;... (3 Replies)
Discussion started by: sb200
3 Replies

10. Solaris

Solaris 10: how to disable an unused HBA card

Dear all, I have a new Oracle Blade X4-2B server, running Solaris 10. The server comes with a HBA card that will not be used now. It has not fibers connected to it. As a consequence, its leds never stop flashing. My question is: how to disable this HBA card, without removing it physically... (2 Replies)
Discussion started by: Gus1971
2 Replies
XI(4)							   BSD Kernel Interfaces Manual 						     XI(4)

NAME
xi -- Xircom CreditCard Ethernet device driver SYNOPSIS
xi* at xirc? Configuration of PHYs may also be necessary. See mii(4). DESCRIPTION
The xi driver provides support for the Xircom CreditCard family of PCMCIA Ethernet adapters. Supported cards include: Xircom CreditCard Ethernet II Xircom CreditCard 10/100 Ethernet Xircom RealPort 10/100 Ethernet + Modem (Ethernet function only) Intel EtherExpress Pro/100 Compaq Netelligent 10/100 Cards which should work, but have not been confirmed include: Xircom RealPort Ethernet Xircom RealPort 10/100 Ethernet Some Xircom Ethernet products are supported by the tlp(4) driver. MEDIA SELECTION
Media selection is done using ifconfig(8) using the standard ifmedia(4) mechanism. Refer to those manual pages for more information. SEE ALSO
ifmedia(4), mii(4), netintro(4), pcmcia(4), tlp(4), xirc(4), ifconfig(8) HISTORY
The xi device driver appeared in NetBSD 1.5. BUGS
The driver suffers from poor performance. Even with the 10/100 cards, do not expect more than ~450KB/s. Some 10/100 cards may not autonego- tiate reliably and require manual media selection. The Xircom multifunction cards which contain both Ethernet and modem interfaces are known to have problems. This is due to the card not reporting itself correctly as a multifunction card. BSD
June 1, 2007 BSD
All times are GMT -4. The time now is 10:48 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy