Solved it by myself, but I should have tought about it earlier.
What I forgot was to NAT the adresses from the 192.168.1.0/24 to the 192.168.2.0/24 adresses.
So what I have done.
- Enabled the IPfilter firewall.
- create the file /etc/ipf/ipnat.conf
- restart ipfilter
HI guys/gals
basic question
lets say i am running a network. lets say i am using Win Me.
how would i network Win Me to a computer that has linux and another that has 98 well the 98 is no problem but the linux well i have an idea but i am rusty with linux. No i have rusted out. Would you make... (1 Reply)
I am trying to network two solaris workstations(ultra sparc 5) at home. what shoud I use to build the one of workstations as a http and ftp server and to network with the other workstation?
(please explain to me in detail.. what kind of software or equipment do I need..)
Thanks
John (1 Reply)
Hi,
I am trying to configure an ip address, netmask, and default gateway on my solaris machine. For example, in Linux I would do the following command:
#ifconfig eth0 xx.xx.xx.xx netmask 255.0.0.0
#add route or route add default xxx.xxx.xxx.xxx
In Solaris 10, I believe the commands are... (7 Replies)
hi all,
how do i make sure that the new routing should take effect on the os memory right away? what should i run after i add all the new "route add ....".
I have an example below:
bash-2.03# netstat -rn
Routing Table: IPv4
Destination Gateway Flags Ref Use Interface... (1 Reply)
I have just installed Solaris 10 for x86. The install seemed to have worked fine, and I have configured my hostname and am able to login and do whatever. However, networking does not seem to have been installed. I have a router which assigns ip address via DHCP. I would have thought Solaris would... (5 Replies)
Hi all
Right, i need to admit Im c4p on networking. I hate it, always have, always will. Here's my problem
Ive got 3 hosts. A B and C. I need to directly contact host C from host A, but at the moment I have to ssh on to B, to then ssh on to C.
so, I need to set up host b, to forward... (3 Replies)
Hi All,
Actually a very basic question this one. I've got a Solaris 10 x86 server box on a network. There are a group of other servers I need to connect to from it, but via a VPN connection. If I install a vpn client on my solaris box, can I configure the VPN connection so it only routes certain... (1 Reply)
Discussion started by: mikecouk
1 Replies
LEARN ABOUT SUSE
ifndp-proxy
IFNDP-PROXY(5) Network configuration IFNDP-PROXY(5)NAME
ifndp-proxy[-<interface name>] - IPv6 NDP and IPv4 ARP proxy entries
SYNOPSIS
/etc/sysconfig/network/ifndp-proxy
/etc/sysconfig/network/ifndp-proxy-<interface name>
DESCRIPTION
These files contain IPv6 NDP and IPv4 ARP proxy settings, that should be applied using the ip neigh add proxy command documented in the
ip(8) manual page that provides a common interface for IPv4 and IPv6.
The NDP/ARP proxy is required, e.g. when IP addresses from the same subnet have to be used on the interface of the host as well as on
interfaces behind a (tunnel) interface and using a bridge is not an option.
Don't forget to enable forwarding and the NDP/ARP proxy by setting
net.ipv6.conf.<all|default|interface name>.proxy_ndp = 1
net.ipv6.conf.<all|default|interface name>.forwarding = 1
and/or
net.ipv4.conf.<all|default|interface name>.proxy_arp = 1
net.ipv4.conf.<all|default|interface name>.forwarding = 1
or
net.ipv4.ip_forward = 1
either as global all setting in the /etc/sysctl.conf file or using the ifsysctl(5) files, that allow per-interface setup.
Forwarding can be also enabled in the /etc/sysconfig/sysctl file using the IP_FORWARD and IPV6_FORWARD variables.
The proxy entries are added and deleted using the if-{up|down}.d/ndp-proxy script, every time after an involved interface has been set
up or down.
SYNTAX
The format of the ifndp-proxy file is:
<address> <address interface> <proxy interface list>
The format of the ifndp-proxy-<address interface> file is same to above, but allows also to omit the address interface by using a "-" as
placeholder inside of the file, because it is already available in the file name:
<address> <address interface | -> <proxy interface list>
Lines beginning with # and blank lines are ignored.
Each line defines to add a proxy NDP/ARP entry with the address of or behind address interface to all interfaces in the proxy interface
list.
EXAMPLES
Let's assume, your machine is connected via eth0 to a switch with the networks 2001:db8:abba::/64 and 192.168.100.1/24 and is using the IP
address 1 itself. You'd like to use the addresses 11 and 12 e.g. for virtual machines behind the tap1 and tap2 interface, that is:
2001:db8:abba::1/64 -- local eth0 address
2001:db8:abba::11/64 -- address behind tap1
2001:db8:abba::12/64 -- address behind tap2
192.168.100.1/24 -- local eth0 address
192.168.100.11/24 -- address behind tap1
192.168.100.12/24 -- address behind tap2
then set up the following entries in the ifndp-proxy file:
2001:db8:abba::1 eth0 tap1 tap2
2001:db8:abba::11 tap1 eth0 tap2
2001:db8:abba::12 tap2 eth0 tap1
192.168.100.1 eth0 tap1 tap2
192.168.100.11 tap1 eth0 tap2
192.168.100.12 tap2 eth0 tap1
additionally to the routing entries in the routes or ifroute-<interface name> files.
BUGS
Please report bugs at <https://bugzilla.novell.com/>
AUTHOR
Marius Tomaschewski <mt@suse.de>
SEE ALSO ifup(8)ifcfg(5)ifsysctl(8)sysconfig December 2009 IFNDP-PROXY(5)