|
|
Sponsored Content
Operating Systems
Solaris
problem network with solaris 10 & vmware
Post 302359325 by capilla on Tuesday 6th of October 2009 09:18:42 AM
10-06-2009
|
|
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi folks!
i've just downloaded the three SOlaris 8 Free install-CDs, then went to install it in a VM on VMware 2.0.3, okay DCA and CD inserted, DCA configured all devices - THEN
at the selection of the boot device - selected CD - getting DISK READ ERROR at sector 120.
Can anyone help?!!!... (1 Reply)
Discussion started by: __kernelpanic
1 Replies
2. UNIX for Dummies Questions & Answers
WEe have installed Intel version of Solaris 8 in a machine .we skipped the network configuration at the begning.we selected unnetworked.Now we need to connect the same machine to a network.
We configured the Card using ifconfig but its taking the ip address itself as the Default G/W.
I need help... (4 Replies)
Discussion started by: premkumar
4 Replies
3. IP Networking
hello
i had soloaris 8 installed . at the beggining it sees my network
card( intel i815/82559 onboard)(my mainboard is GA-8IRXP);
but during the installation when I fill the ip address and the dns
at the end that i should confirm it says:
no dns find (i'm sure about the dns... (4 Replies)
Discussion started by: hessam
4 Replies
4. Linux
Hi all,
I tried to install Solaris 10 and then VMware ESX server v3.02 on the same PC (or hard drive). But after successfully installing Solaris 10, when I installed Vmware ESX Server on the same drive(but on different partition, boot menu is not coming.
It is just booting Vmware only.
Pls... (1 Reply)
Discussion started by: vikas027
1 Replies
5. Solaris
I am running solaris 10 on VMware and I do not know how to setup the USB drive. After refer to few doc from sun still unable to get what i should do.
Can someone help?
On VMware I have added a USB controller.
Oh yes, from prtconf and dmesg, it don't seem to reganize the usb controller. I... (0 Replies)
Discussion started by: ezsurf
0 Replies
6. Solaris
Hi there,
I run a SunFire v245 with solaris 10. I run a custom ERP on that. my clients are connecting via telnet and run the application...
my last "server" was a sun blade 100 with solaris 8, everything was running correctly.
Since I have the new server, I have many problem with my... (5 Replies)
Discussion started by: Siffleu
5 Replies
7. Solaris
Hi all,
I have install sun solaris 10 on vmware server and i cant ping the solaris guest machine from the host and vice versa.
The enable network card in the host machine is an wifi card so I know that i can't use bridged network from Vmware.
I tried to use host or NAT but it seem not to work... (1 Reply)
Discussion started by: papiseckfr
1 Replies
8. Solaris
Hi All,
We have configured an hp network printer on a Solaris-sparc machine.
We are unable to print any files from this machine.
The following are the other details:
lpstat -p hpnic -l
printer hpnic waiting for auto-retry. available.
exec exit fault
Form mounted:
... (0 Replies)
Discussion started by: shahshilpa
0 Replies
9. UNIX for Advanced & Expert Users
I am going to take up a position in Data & Network Security.
I would need to write network shell scripts doing the following task:
Going to around 2000 servers and findout which groups has access to each servers and which ids are there in each group that has access.
I need to implement... (1 Reply)
Discussion started by: pinnacle
1 Replies
10. Solaris
Hello all, thanks for reading my question:
So I've been a Unix/Linux SysAdmin for a couple years, and I'm a bit over my head running solo, trying to set up LDoms using Oracle VM Server 3.1 for SPARC. I've been very careful, and things have gone well up until the point I try to access the new... (9 Replies)
Discussion started by: Lyxix
9 Replies
LEARN ABOUT DEBIAN
pbuilder-uml.conf
pbuilder-uml.conf(5) pbuilder pbuilder-uml.conf(5) NAME
pbuilder-uml.conf - configuration file for user-mode-linux port of pbuilder DESCRIPTION
/etc/pbuilder/pbuilder-uml.conf contains default values used in pbuilder-user-mode-linux program invocation. FORMAT
MY_ETH0=tuntap,,,192.168.0.2 Configures ethernet setting used for booting linux. See how rootstrap boots your system, and copy that. Specify --eth0=slirp,12345,/usr/bin/slirp-fullbolt to use the slirp connection. UML_IP=192.168.0.3 IP address to use for guest OS. This can be set to dhcp for obtaining IP address through DHCP. UML_NETMASK=255.255.255.0 Guest OS netmask UML_NETWORK=192.168.0.0 Guest OS network UML_BROADCAST=255.255.255.255 Guest OS broadcast UML_GATEWAY=192.168.0.1 Guest OS gateway PBUILDER_UML_IMAGE=${HOME}/uml-image Guest OS file system image. UML_MOUNT_TMPFS=no Whether to mount tmpfs inside the guest image. This is probably mostly useless. BUILDPLACE=${HOME}/tmp/ The location which build will take place. pbuilder-user-mode-linux will place temporary COW files to there. The user running UML needs to be able to access that directory. UML_MEM=128 The amount of memory allowed for UML. Give more value to here. UML_HOSTNAME=uml-host The hostname for the UML. The hostname should be available in /etc/hosts so that hostname -f will be able to return the FQDN. UML_BUILDRESULT=/directory/of/build/result The directory where build result of pbuilder-user-mode-linux is stored. ROOTSTRAP_IMAGESIZE=size-in-megabytes The size, in MB, of the disk iamge to create. Defaults to 1000. NOTES
It is advised to set APTCACHEHARDLINK to no in ~/.pbuilderrc. see pbuilderrc(5) for details. AUTHOR
Initial coding, and main maintenance is done by Junichi Uekawa <dancer@debian.org>. The homepage is available at http://pbuilder.alioth.debian.org FILES
/etc/pbuilder/pbuilder-uml.conf, ${HOME}/.pbuilderrc SEE ALSO
/usr/share/doc/pbuilder/pbuilder-doc.html, pbuilder-user-mode-linux(1), pbuilder(8), pbuilderrc(5), pdebuild(1) Debian 2003 Jan 8 pbuilder-uml.conf(5)