Hi All
I've been having a lot of errors logged on the Cisco Catalyst (4000 series) which one of my Solaris servers is patched into. I have a feeling they are duplex related, but I'm a bit stuck as to how to confirm that.
How do I:
1. Check the duplex settings on my eri0 card?
2. Set the... (3 Replies)
I have a TOSHIBA AS7000 B150 Sun Box
I wanted to run it with 100M/full duplex
I had added this to the /etc/system file to make to setting permenant So it would be set correctly on reboot.
set eri:eri_adv_100fdx_cap=1
set eri:eri_adv_100hdx_cap=0
set eri:eri_adv_autoneg_cap=0
But when I... (4 Replies)
Hi there
We have a bit of a debate going here over what the prefered method is for setting 1000/Full on e1000g or nge interfaces is.
As you aware the Solaris configration files for nge and e1000g dont allow you to "fix" 1000/Full but instead allow you to set auto-negotiate to ON but only... (1 Reply)
I would like to change half duplex to full duplex on solaris 5.5. I tried with below commands but they didnt work on solaris 5.5.
#ndd -set /dev/le adv_100fdx_cap 1 (6 Replies)
Hi,
In UNIX, it's very easy to find the duplex speed. But in Windows, is there a easy way to find the duplex speed? I can't go to over 100 servers to find this out, I was wondering if I run one command to do this?
Please advice. (2 Replies)
Hi,
How to find whether the server is running with half duplex or full duplex. I tried with the following command ndd -get /dev/ but am not getting any output,. Is the command correct?
Also let me know how to change from half to full duplex. (1 Reply)
How to change Speed Duplex !
How to change Speed Duplex by command
chdev -P -l ent1 -a media_speed=1000_Full_Duplex
How to change Speed Duplex by Smitty .
smitty chgenet -> select adapter -> change Media speed etc. -> set "Apply change to DATABASE only" to yes -> Enter -> ... (0 Replies)
VIO Server connected to switch port and running with half duplex speed on one of the shared ethernet adapter. We have verified at switch end and everythings looks good.
Other ethernet adapter in the VIO server are connected and running in Full duplex speed.
Please help me find why this shared... (4 Replies)
So I have a server I am trying to set up a script to send a Wall message notifying of my eth0 nic being set to 100 half duplex instead of 100 full duplex.
I know I am trying to read from /etc/sysconfig/network/ifcfg-eth0 to pull the parameters
STARTMODE=onboot
BOOTPROTO=static... (6 Replies)
Discussion started by: lutador72
6 Replies
LEARN ABOUT NETBSD
bge
BGE(4) BSD Kernel Interfaces Manual BGE(4)NAME
bge -- Broadcom BCM570x family Gigabit Ethernet driver
SYNOPSIS
bge* at pci? dev ? function ?
Configuration of PHYs may also be necessary. See mii(4).
DESCRIPTION
The bge device driver supports Gigabit Ethernet interfaces based on the Broadcom BCM570x family of Gigabit Ethernet chips and the BCM5906
chip. The interfaces supported by the bge driver include:
o 3Com 3c996-T (10BASE-T/100BASE-TX/1000BASE-T)
o Dell PowerEdge 2550 integrated BCM5700 NIC (10BASE-T/100BASE-TX/1000BASE-T)
o IBM x235 server integrated BCM5703x NIC (10BASE-T/100BASE-TX/1000BASE-T)
o Netgear GA302T (10BASE-T/100BASE-TX/1000BASE-T)
o SysKonnect SK-9D21 (10BASE-T/100BASE-TX/1000BASE-T)
o SysKonnect SK-9D41 (1000BASE-SX)
The BCM570x family supports IPv4/TCP/UDP checksumming in hardware. The bge driver supports this feature of the chip. See ifconfig(8) for
information on how to enable this feature.
The level of interrupt mitigation for received packets can be adjusted with the hw.bge.rx_lvl sysctl(8) control. A value of 1 yields a bge
interrrupt for every two full-sized Ethernet frames. Each increment of the value will, roughly, halve receive interrupt rate, up to a maxi-
mum of 5, which interrupts about every 30 to 40 full-sized TCP segments.
SEE ALSO arp(4), bce(4), ifmedia(4), mii(4), netintro(4), pci(4), ifconfig(8)HISTORY
The bge driver first appeared in NetBSD 1.6.1.
AUTHORS
The bge driver was written by Bill Paul <wpaul@windriver.com> for FreeBSD and ported to NetBSD by Frank van der Linden
<fvdl@wasabisystems.com>, Jason R. Thorpe <thorpej@wasabisystems.com> and Jonathan Stone <jonathan@dsg.stanford.edu>.
BSD September 26, 2009 BSD