08-16-2009
restart the network on freeBSD 7.2
hi
howto restart the network with a wireless interface including wpa_supplicant on freeBSD 7.2 without reboot?
9 More Discussions You Might Find Interesting
1. Programming
Hello there,
My mulithreaded application (which is too large to represent the source code here) is crashing after installing FreeBSD 7.1-RELEASE/amd64.
It worked properly on others machines (Dual Cores with 4GB of RAM - FreeBSD 6.2-RELEASE/i386).
The current machine has 2x Core 2 Duo... (1 Reply)
Discussion started by: Seenquev
1 Replies
2. Programming
I am developing a Network Appliation to monitor computers in a network.
Specs are
App monitors the current web page viewed in each system
App also can shutdown the computer in the network
App can show all process run by each computer in the network
I am now confused how to start my... (2 Replies)
Discussion started by: valaparambil88
2 Replies
3. IP Networking
hello i have a ubuntu ssh server that i can acess from any of my comnputers but only if they are on the same wireless network as the server. i tested trhis my tehtehring my samsung blackjack to my windows partition and installing openssh to windows it works when windows is on the wireless but no... (1 Reply)
Discussion started by: old noob
1 Replies
4. AIX
Hi All,
Please let me know the command to restart the network interface and enable it on boot in AIX, similar to /etc/init.d/network restart in Redhat.
Thanks,
Sunil.K
please watch out to post in the right subforum! (9 Replies)
Discussion started by: sunilrk07
9 Replies
5. IP Networking
Hello,
I'm attempting to setup a test network with a client-server based architecture using a proprietary application. The client works by communicating with the server on separate links (typically cellular connections) and then initiates a tunnel over each active link. However, in place of the... (0 Replies)
Discussion started by: shadyuk
0 Replies
6. Red Hat
Hi,
I have 2 machines in production environment:
1. redhat machine for application
2. DB machine (oracle)
The application doing a lot of small read&writes from and to the DB machine.
The problem is that after some few hours the network from the application to the DB becomes very slow and... (4 Replies)
Discussion started by: moshesa
4 Replies
7. IP Networking
My son does homework on a school laptop. I was thinking about setting up a gateway on my home network, so that I can monitor web traffic and know if he is doing his homework without standing over his shoulder. Ideally I would like to use the Raspberry Pi Model b that I already have. However, I... (15 Replies)
Discussion started by: gandolf989
15 Replies
8. Solaris
Hi all,
First post here. Working on Solaris 10, on a Sun t4-4, need to change RX queue depth(ethernet, not HBA) and was wondering if i could get by with just restarting the network or if i should just bounce the whole shebang.
Apologies if i missed a similar thread. if there is one, please... (2 Replies)
Discussion started by: caspnx
2 Replies
9. Debian
Hello,
I would like to do follow steps.
Set a static IP-Adress on eth0 (For Testing)
Set DHCP on eth0
All steps should be done without a single reboot.
/etc/network/interfaces
iface eth0 inet static
address 192.0.2.7/24
gateway 192.0.2.254How do i perform... (3 Replies)
Discussion started by: int3g3r
3 Replies
URTW(4) BSD Kernel Interfaces Manual URTW(4)
NAME
urtw -- Realtek RTL8187B/L USB IEEE 802.11b/g wireless network device
SYNOPSIS
To compile this driver into the kernel, place the following lines in your kernel configuration file:
urtw* at uhub? port ?
DESCRIPTION
The urtw driver supports USB 802.11b/g wireless adapters based on the Realtek RTL8187B/L.
urtw supports station and monitor mode operation. Only one virtual interface may be configured at any time. For more information on config-
uring this device, see ifconfig(8).
HARDWARE
The urtw driver supports Realtek RTL8187B/L based wireless network devices, including:
Card Radio Bus
Belkin F5D7050E RTL8225 USB
Linksys WUSB54GCv2 RTL8225 USB
Netgear WG111v2 RTL8225 USB
Netgear WG111v3 RTL8225 USB
Safehome WLG-1500SMA5 RTL8225 USB
Shuttle XPC Accessory PN20 RTL8225 USB
Sitecom WL168v1 RTL8225 USB
Sitecom WL168v4 RTL8225 USB
SureCom EP-9001-g(2A) RTL8225 USB
TRENDnet TEW-424UB V3.xR RTL8225 USB
EXAMPLES
ifconfig.if(5) example configures urtw0 to join whatever network is available on boot, using WEP key ``0x1deadbeef1'', channel 11, obtaining
an IP address using DHCP:
nwkey 0x1deadbeef1 chan 11
dhcp
Configure urtw0 to join network ``my_net'' using WPA with passphrase ``my_passphrase'':
# ifconfig urtw0 nwid my_net wpakey my_passphrase
Join an existing BSS network, ``my_net'':
# ifconfig urtw0 192.168.1.1 netmask 0xffffff00 nwid my_net
SEE ALSO
arp(4), netintro(4), usb(4), ifconfig.if(5), wpa_supplicant.conf(5), ifconfig(8), wpa_supplicant(8)
Realtek, http://www.realtek.com.tw.
HISTORY
The urtw device driver first appeared in FreeBSD 8.0.
AUTHORS
The urtw driver was written by Weongyo Jeong <weongyo@FreeBSD.org>.
BSD
October 17, 2009 BSD