08-16-2009
restart the network on freeBSD 7.2
hi
howto restart the network with a wireless interface including wpa_supplicant on freeBSD 7.2 without reboot?
9 More Discussions You Might Find Interesting
1. Programming
Hello there,
My mulithreaded application (which is too large to represent the source code here) is crashing after installing FreeBSD 7.1-RELEASE/amd64.
It worked properly on others machines (Dual Cores with 4GB of RAM - FreeBSD 6.2-RELEASE/i386).
The current machine has 2x Core 2 Duo... (1 Reply)
Discussion started by: Seenquev
1 Replies
2. Programming
I am developing a Network Appliation to monitor computers in a network.
Specs are
App monitors the current web page viewed in each system
App also can shutdown the computer in the network
App can show all process run by each computer in the network
I am now confused how to start my... (2 Replies)
Discussion started by: valaparambil88
2 Replies
3. IP Networking
hello i have a ubuntu ssh server that i can acess from any of my comnputers but only if they are on the same wireless network as the server. i tested trhis my tehtehring my samsung blackjack to my windows partition and installing openssh to windows it works when windows is on the wireless but no... (1 Reply)
Discussion started by: old noob
1 Replies
4. AIX
Hi All,
Please let me know the command to restart the network interface and enable it on boot in AIX, similar to /etc/init.d/network restart in Redhat.
Thanks,
Sunil.K
please watch out to post in the right subforum! (9 Replies)
Discussion started by: sunilrk07
9 Replies
5. IP Networking
Hello,
I'm attempting to setup a test network with a client-server based architecture using a proprietary application. The client works by communicating with the server on separate links (typically cellular connections) and then initiates a tunnel over each active link. However, in place of the... (0 Replies)
Discussion started by: shadyuk
0 Replies
6. Red Hat
Hi,
I have 2 machines in production environment:
1. redhat machine for application
2. DB machine (oracle)
The application doing a lot of small read&writes from and to the DB machine.
The problem is that after some few hours the network from the application to the DB becomes very slow and... (4 Replies)
Discussion started by: moshesa
4 Replies
7. IP Networking
My son does homework on a school laptop. I was thinking about setting up a gateway on my home network, so that I can monitor web traffic and know if he is doing his homework without standing over his shoulder. Ideally I would like to use the Raspberry Pi Model b that I already have. However, I... (15 Replies)
Discussion started by: gandolf989
15 Replies
8. Solaris
Hi all,
First post here. Working on Solaris 10, on a Sun t4-4, need to change RX queue depth(ethernet, not HBA) and was wondering if i could get by with just restarting the network or if i should just bounce the whole shebang.
Apologies if i missed a similar thread. if there is one, please... (2 Replies)
Discussion started by: caspnx
2 Replies
9. Debian
Hello,
I would like to do follow steps.
Set a static IP-Adress on eth0 (For Testing)
Set DHCP on eth0
All steps should be done without a single reboot.
/etc/network/interfaces
iface eth0 inet static
address 192.0.2.7/24
gateway 192.0.2.254How do i perform... (3 Replies)
Discussion started by: int3g3r
3 Replies
LEARN ABOUT ULTRIX
reboot
reboot(2) System Calls Manual reboot(2)
Name
reboot - reboot system or halt processor
Syntax
#include <sys/reboot.h>
reboot(howto)
int howto;
Arguments
howto The howto argument is a mask of options passed to the bootstrap program.
The bits of howto are:
RB_HALT
the processor is simply halted; no reboot takes place. RB_HALT should be used with caution.
RB_ASKNAME
Interpreted by the bootstrap program itself, causing it to inquire as to what file should be booted. Normally, the system
is booted from the file "xx(0,0)vmunix" without asking.
RB_SINGLE
Normally, the reboot procedure involves an automatic disk consistency check and then multi-user operations. RB_SINGLE pre-
vents the consistency check, rather simply booting the system with a single-user shell on the console. RB_SINGLE is inter-
preted by the init(8) program in the newly booted system. This switch is not available from the system call interface.
Only the superuser may a machine.
Description
The system call reboots the system, and is invoked automatically in the event of unrecoverable system failures. The system call interface
permits only RB_HALT or RB_AUTOBOOT to be passed to the reboot program; the other flags are used in scripts stored on the console storage
media or used in manual bootstrap procedures. When none of these options (for example, RB_AUTOBOOT) is given, the system is rebooted from
file in the root file system of unit 0 of a disk chosen in a processor-specific way. Normally, an automatic consistency check of the disks
is then performed.
Return Values
If successful, this call never returns. Otherwise, a -1 is returned, and an error is stored in the global variable errno.
Diagnostics
The call fails under the following condition:
[EPERM] The caller is not the superuser.
See Also
crash(8v), halt(8), init(8), reboot(8)
reboot(2)