06-29-2009
Hi
Yes I've worked with the T3's before, used them in an Oracle Veritas Cluster at the time. Hardware RAID if I remember correctly but we only had a pair of them. We had a bad experience with it due to bad firmware which meant we lost one of the RAID 5 sets on it and had to recover from tape - not a very nice thing to happen.
All was ok with it once the firmware was updated but never had any confidence in it after that although it ran perfectly for 18 months after that before we replaced it.
Quite a bit newer than the other two bits of kit you've seen, still EOL but Sun have stated they will support it till 2011 if you pay them so spares should be around till then I would have thought.
I'd say its quite a bit more complicated than the A1000 or 5200 to set up but there should be plenty of documentation around if needed.
I'm not saying the T3 is a bad bit of kit, just my experience with it was one best forgotten.
9 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Hi,
I am a Dba and very new to filesystems and stuff.
I think that we have Veritas filesystems on my Sun SOlaris 5.8 box, how do I confirm this: all my filesystems are mounted like this:
/dev/vx/dsk...
Now we are also using disk arrays (storedge a1000) how do I access them from the system.... (1 Reply)
Discussion started by: knarayan
1 Replies
2. UNIX for Advanced & Expert Users
Hi,
I'm facing problem in connecting a Raid A1000 to E250 and E450. ( Both machines with Solaris 2.6 OS and patched, with different
scsi-initiator-ids - 7 & 3 ).
BTW, I'm not using this setup to access raid data from both machines simultaneously. There is Veritas Cluster Server monitoring... (1 Reply)
Discussion started by: shibz
1 Replies
3. UNIX for Dummies Questions & Answers
After searching and finding the link to the A1000 pdf ( http://192.18.99.138/805-7147/805-7147.pdf ) my questions are:
1) I have a battery failure on a A1000. I know that caching is disabled and it reports to see log. After reading the manual I have learned that the battery is a data-cache... (2 Replies)
Discussion started by: finster
2 Replies
4. Solaris
Sorry if this seems trivial. i have been given a task at work to configure a sun processing server "enterprise 4500" so it can work with the a storage server "storedge A5200" and "storedge D1000"
the truth is i have never worked on a sun server before. i need a guideline (step by step) as to... (5 Replies)
Discussion started by: lawalidowu
5 Replies
5. Solaris
I have a SUN Blade 1000 running Solaris 10 and an A1000 array.
I know that this combo is not supported by SUN but will it work?
The raid manager software is installed and it says that the firmware needs to be upgraded -it is at I think level 2.05 something.
I can see all the disks in a... (13 Replies)
Discussion started by: tribbles
13 Replies
6. Solaris
Hello Experts,
I am using E250 on that solais 10 5/08 installed. I am unable to see disks. I connected 2 disks in that storage of 18gb each. When I run format command it is showing that 2 disks one is operating system and another one is 6MB. I checked probe-scsi and probe-scsi-all at ok... (6 Replies)
Discussion started by: younus_syed
6 Replies
7. Solaris
I am new to the unix world. I have SunBlade 100 and A1000 Disk storage array with 12 Hard drives. I used SCSI card and SCSI cables to connect. When I do the format command,I can see disk storage as one disk instead of 12 disks as below. Could anybody can explain why?
What should I do in order... (1 Reply)
Discussion started by: Dulasi
1 Replies
8. Solaris
hi friends how we can create luns in A1OOO storage ..plzhelp its very urgent
when ever i am connect to A1000 raid controller through laptop with console cable with the help of hyperterminal..i isued serial port parameters which i mentioned below..
Set serial port parameters to:
�... (1 Reply)
Discussion started by: tv.praveenkumar
1 Replies
9. Solaris
I would want to ask on what software do i need to configure disk array for StorEdge A1000. (Sun Enterprise 450 - currently installed with SUN Solaris 9.)
Is it using RAID Manager 6.22? And is it compatible with SUN Solaris 9 or 10?
Thanks in advance for reading or replying my post. (2 Replies)
Discussion started by: beginningDBA
2 Replies
LEARN ABOUT NETBSD
apmlabel
APMLABEL(8) BSD System Manager's Manual APMLABEL(8)
NAME
apmlabel -- update disk label from Apple Partition Map
SYNOPSIS
apmlabel [-fqrw] device
DESCRIPTION
apmlabel is used to update a NetBSD disk label from the Apple Partition Map found on disks that were previously used on Mac OS systems (or
other APM using systems).
apmlabel scans the APM contained in the first blocks of the disk and generates additional partition entries for the disk from the entries
found. Driver and patches partitions are ignored.
Each APM entry which does not have an equivalent partition in the disk label (equivalent in having the same size and offset) is added to the
first free partition slot in the disk label. A free partition slot is defined as one with an fstype of 'unused' and a size of zero ('0').
If there are not enough free slots in the disk label, a warning will be issued.
The raw partition (typically partition c, but d on i386 and some other platforms) is left alone during this process.
By default, the proposed changed disk label will be displayed and no disk label update will occur.
Available options:
-f Force an update, even if there has been no change.
-q Performs operations in a quiet fashion.
-r In conjunction with -w, also update the on-disk label.
-w Update the in-core label if it has been changed.
SEE ALSO
disklabel(8), dkctl(8), pdisk(8)
HISTORY
The apmlabel command appeared in NetBSD 5.0.
BSD
May 19, 2007 BSD