|
|
Sponsored Content
Special Forums
IP Networking
what is wrong with VLAN???
Post 302321165 by samar on Saturday 30th of May 2009 05:29:56 PM
05-30-2009
what is wrong with VLAN???
Hi all,
so server: FreeBSD 7.0 release,
interfaces on it DLINK DGE-528T with support of vlans
)
so first interface looks to LAN second to ISP.
I created vlan1 with id 1 and gave to it ip address and plug it in
tagged port of swith for vlan 1. so client from vlan1 reaches the server.
it pings it. but it in no way doenst want to go internet via squid.
same thing works with NAT. i translated traffic from that vlan with nat,
and it works fine, but not with squid.
So what is wrong here???? does squid not support VLAN????
I'm really confused, SOS ...
so server: FreeBSD 7.0 release,
interfaces on it DLINK DGE-528T with support of vlans
)so first interface looks to LAN second to ISP.
I created vlan1 with id 1 and gave to it ip address and plug it in
tagged port of swith for vlan 1. so client from vlan1 reaches the server.
it pings it. but it in no way doenst want to go internet via squid.
same thing works with NAT. i translated traffic from that vlan with nat,
and it works fine, but not with squid.
So what is wrong here???? does squid not support VLAN????
I'm really confused, SOS ...
|
|
10 More Discussions You Might Find Interesting
1. Solaris
hi,
i tried to configure an VLAN interface on my SF280 based on the documentation on docs.sun.com
# ifconfig eri1000 plumb up
Oct 21 13:41:26 cmsmaster ip: ip_rput_dlpi(eri1000): DL_ERROR_ACK for DL_ATTACH_REQ(11), errno 8, unix 0
ifconfig: SIOCSLIFNAME for ip: eri1000: no such interface... (2 Replies)
Discussion started by: pressy
2 Replies
2. Solaris
I 've a T5220 running solaris 10u6 with Ldoms 1.1. following is o/p of my dladm
e1000g0 type: non-vlan mtu: 1500 device: e1000g0
e1000g1 type: non-vlan mtu: 1500 device: e1000g1
e1000g531001 type: vlan 531 mtu: 1500 device: e1000g1
e1000g2 ... (0 Replies)
Discussion started by: fugitive
0 Replies
3. AIX
I have a aix 5.3, two network adapter, configure as a etherchannel, how can I know the vlan id by command? (4 Replies)
Discussion started by: rainbow_bean
4 Replies
4. Programming
Hi all
My application is a monitoring application that monitors the incoming udp packet when ever required. When ever a particular source ip and port and dest ip and port is provided the filter will be framed based them. For eg,
char filterExpr;
filterExpr = "udp and src host 192.168.16.100... (0 Replies)
Discussion started by: anusha_pixel
0 Replies
5. IP Networking
Hello. I want to Communicate 2 VLAN with router like this solution:
http://8pic.ir/images/83m0ouih8mmm9s1sfl56.jpg
For this purpose I'm configuring 2 Linux system as a switch and connect 4 host to them. Then a router is added to scenario.
The configuration of the switches is:
On DUT1(Linux):... (1 Reply)
Discussion started by: zsn
1 Replies
6. Solaris
Hi,
Is it possible to VLAN tag with a ce interface on Solaris 9? Link speed is gb.
ce:0:ce0:link_speed 1000
I have a ce0 interface I would need to have access to another VLAN as well as the one it's currently on.
What commands would I need to run?
Thanks.;) (2 Replies)
Discussion started by: sparcman
2 Replies
7. Red Hat
We have two hosts in same vlan with same route rules.
One of them is not able to connect to an outside IP while in another I get "failed: Connection timed out" while testing the connectivity through netcat.
I have tried mtr /traceroute and it gives me the same results.
Is there a netcat... (1 Reply)
Discussion started by: jacki
1 Replies
8. Solaris
Have 2 nics on physical system
net0 phys 1500 up --
net1 phys 1500 up --
1. I want to create a link aggregation with LACP enabled with above 2 nics
2. Create port-group(Like we create on ESXi) with VLAN-ID 2141
3. And assign this... (0 Replies)
Discussion started by: Shirishlnx
0 Replies
9. AIX
Hi Guys,
Our lpars is currently running on 2 different vlans (20, 30). Now we have a requirement that vlan 30 needs to be change to vlan 31 at the same subnet. I'm not sure on what is the best approach for this or what change is involve on the AIX side.
This is our setup.
Network switch -... (5 Replies)
Discussion started by: kaelu26
5 Replies
10. Solaris
Hi Folks,
I am currently moving systems to a new environment, with some changes to the network requirements on the systems.
One of these changes is moving from just standard IPMP to using IPMP on top of a VLAN, I have used VLAN tagging befor without issue - however not with IPMP.
What I... (2 Replies)
Discussion started by: gull04
2 Replies
LEARN ABOUT NETBSD
stge
STGE(4) BSD Kernel Interfaces Manual STGE(4) NAME
stge -- Sundance/Tamarack TC9021 Gigabit Ethernet driver SYNOPSIS
stge* at pci? dev ? function ? Configuration of PHYs or Ten-bit interfaces may also be necessary. See mii(4). DESCRIPTION
The stge device driver supports the Sundance/Tamarack TC9021 Gigabit Ethernet chip. The Sundance/Tamarack TC9021 is found on the D-Link DGE-550T, and the Antares Microsystems Gigabit Ethernet board. It uses an external PHY or an external 10-bit interface. The TC9021 supports IPv4/TCP/UDP checksumming in hardware. The stge driver supports this feature of the chip. See ifconfig(8) for informa- tion on how to enable this feature. SEE ALSO
arp(4), ifmedia(4), mii(4), netintro(4), pci(4), ifconfig(8) HISTORY
The stge driver first appeared in NetBSD 1.6. AUTHORS
The stge driver was written by Jason R. Thorpe <thorpej@NetBSD.org>. BUGS
The stge driver does not support the VLAN tag insertion/removal feature of the TC9021 chip. This is primarily because the TC9021's VLAN do not have a useful programming interface. The stge driver does not yet support jumbo Ethernet frames. The stge driver does not yet function properly with 1000BASE-T fitted boards. Currently, only 1000BASE-SX boards work. BSD
July 24, 2001 BSD